dodge man

Member
i sent my key for repair bat went flat and now wont take EKA code it would only start before with EKA code before i sent remote i cant get remote to work as well side repeater flashes when i try to put code in dash comes up with its checks windows sunroof some of pickcels on dash is missing so cant see every thing on there some one said somthing about sill buton were is that am at a loss with it now got it moted and cant use it help please john
 
If it will no longer accept the EKA code, it could be the drivers door lock micro switches have failed, do Marty's micro switch test, it's in the tech archive. Otherwise, if you have made too many failed EKA attempts, the BECM may be locked.
 
If it will no longer accept the EKA code, it could be the drivers door lock micro switches have failed, do Marty's micro switch test, it's in the tech archive. Otherwise, if you have made too many failed EKA attempts, the BECM may be locked.
i opened door every time i put code in iv been told that stops it locking the becm up
 
i opened door every time i put code in iv been told that stops it locking the becm up

Only if the microswitches are working.

iirc it says there's a timeout period if the EKA fails to go in after the 3rd attempt.

Where in the country are you and what engine / year is it? Someone nearby might have a Nanocom.
 
Only if the microswitches are working.

iirc it says there's a timeout period if the EKA fails to go in after the 3rd attempt.

Where in the country are you and what engine / year is it? Someone nearby might have a Nanocom.
atherton / m46ory when i unlock door with key it unlocks all the doors and tail gate thanks john
 
if i short the solanoed out it spins over but wont start cos imobilizer on
The sequence of events is normally that when the BECM receives a valid FOB code, it repeatedly sends the mobilisation code to the engine ECU. If the FOB does not work, entry of the EKA code initiates the sending of the mobilisation code.
You really need a Nanocom to see what is going on.
Are there any messages on the dash like "Engine disabled"? Or "Enter EKA"?
If the BECM will not accept the EKA and the FOB doesn't work you have a problem.
I ask again, what is the battery voltage? Low battery volts will cause all sorts of problems.
 
Only if the microswitches are working.

iirc it says there's a timeout period if the EKA fails to go in after the 3rd attempt.

Where in the country are you and what engine / year is it? Someone nearby might have a Nanocom.
uk and and atherton manchester thanks
 
The sequence of events is normally that when the BECM receives a valid FOB code, it repeatedly sends the mobilisation code to the engine ECU. If the FOB does not work, entry of the EKA code initiates the sending of the mobilisation code.
You really need a Nanocom to see what is going on.
Are there any messages on the dash like "Engine disabled"? Or "Enter EKA"?
If the BECM will not accept the EKA and the FOB doesn't work you have a problem.
I ask again, what is the battery voltage? Low battery volts will cause all sorts of problems.
i will try to fined my avo to see what volts are there cant get the fob to work it was operning with the key using the EKA code i used it got it moted the sent key away and bat went flat it has not run since thanks john
 
The sequence of events is normally that when the BECM receives a valid FOB code, it repeatedly sends the mobilisation code to the engine ECU. If the FOB does not work, entry of the EKA code initiates the sending of the mobilisation code.
You really need a Nanocom to see what is going on.
Are there any messages on the dash like "Engine disabled"? Or "Enter EKA"?
If the BECM will not accept the EKA and the FOB doesn't work you have a problem.
I ask again, what is the battery voltage? Low battery volts will cause all sorts of problems.
some of the pickcels are out on the dash so hard to see do all the windows have to be up and does it display that on the dash when you have door open and ignition on thanks
 
some of the pickcels are out on the dash so hard to see do all the windows have to be up and does it display that on the dash when you have door open and ignition on thanks
To clear the "windows not set" messages, each window has to go fully down and then fully up with the ignition on. If there is a sunroof that also has to go through the setting procedure.
 
Do we know what year and engine?

Yes windows are the same regardless of year.

Has the new key been synced?
if the key opens all the doors does it close all?



J
 
Do we know what year and engine?

Yes windows are the same regardless of year.

Has the new key been synced?
if the key opens all the doors does it close all?



J
hi its 2.5 bm disel 1979 the key wont sync in does nothing new battery the key opens and shuts all doors thanks EKA code worked before main bat went flat now does not work
 

Similar threads