al-one-arm

al-one-arm

Well-Known Member
when standing in front of the car, at the rear left there is a rubber pipe , coming from rocker cover up 1.5" then across 6" to the side of the plenum chamber.
question 1; what is the part number for this pipe?
question 2, this pipe fits onto a fitting into the plenum chamber, should you be able to blow through this? or pass anything through it? its a six sided nut with a pipe fitting sticking out
any help would be appreciated
alan

looks like the answer to question 1 is either llh 500100 or llh 500090
 
Last edited:
al-one-arm said:
when standing in front of the car, at the rear left there is a rubber pipe , coming from rocker cover up 1.5" then across 6" to the side of the plenum chamber.
question 1; what is the part number for this pipe?
question 2, there is a fitting into the plenum chamber, should you be able to blow through this? or pass anything through it? its a six sided nut with a pipe fitting sticking out
any help would be appreciated
alan

looks like the answer to question 1 is either llh 500100 or llh 500090
Click to expand...

A picture is worth a thousand words.
 
as name suggests. only have one arm, can't use a mobile very well, so never learnt how to take pics and put them onto computer, so i have editted the front page to make it easier to know what i am on about.lol
 
As above it is part of the crankcase breather setup.....and it shouldn,t be blocked.
 
would spraying carb cleaner into the pipe fitting, clean it out ,without doing any damage, or should i use a small drill?
 
Depends what it's blocked with. Should only be a bit of oily sludge in there, unless someone's blocked it off deliberately.
 
took the pipe fitting off of plenum chamber (22mm spanner) tried air at 100 psi no go, carb cleaner just stayed in there,held a small 3mm drill in hand and twisted it gently, when removed , just black stuff on the end so kept going by hand and eventually it went all the way through. cleaned it out completely . refitted it started car, you could feel the suction from it.temporarily fitted pipe to rocker cover, blew through it ok.
refitted cleaned out rubber pipe and job done.
 
Did you remove/ clean the separator as well? If it's been sitting there with nothing blowing/ sucking through it, it's likely to be bunged up as well
 
where is the separator?
mine just has one pipe from rocker cover to plenum side on left and one pipe from rocker cover to air intake on right side ,all pipes and rocker covers now blow through easily
 
al-one-arm said:
where is the separator?
mine just has one pipe from rocker cover to plenum side on left and one pipe from rocker cover to air intake on right side ,all pipes and rocker covers now blow through easily
Click to expand...
Inside the tube in top of rh rocker cover that the hose pushes over. I linked to it above
 
there is not one of them plastic spiral things anywhere on my car
if it should have one or two i will have to get them
 
The Gods in the Parts Department need to look in their parts manual then. All the P38 V8's have them...
It's the thing I've highlighted in yellow and it goes where I've put the red arrow.
u42CQL7.jpg
 
thats not my rocker covers, that looks like a thors engine not gems
1, my filler neck is on the front right cover
2, my breather pipe(11) is not that shape, its more like item 14 with the last couple of bends cut off.
 
Last edited:
You must log in or register to reply here.

Similar threads

styleruk
2.25 petrol rough idle
2 3
Replies
44
Views
2K
styleruk
styleruk
nevillen
Not As Easy To Re-Jack Point L322 As Thought
2
Replies
32
Views
4K
nevillen
nevillen
hef19898
3.5 V8 Carb Engine Blow Back after cam Shaft replacement
2 3
Replies
40
Views
5K
hef19898
hef19898
Al2O3
Oil Pressure in Different Parts of the Engine
Replies
8
Views
1K
Al2O3
Al2O3
htr
Freelander 1 My Winter Project
2
Replies
35
Views
4K
rob_bell
rob_bell