Seriously tho.

Can you not use a ratchet strap to hold it in place somehow while you offer up the cradle then pull the strap out?

Cheers
 
Can you not fit it thru any of the small cross bars that support the boot floor. Long time since I have looked but is there not small channel where the boot floor is scolloped for strength?

Or even a thin rope just to support an empty tank.

Cheers
 
From memory when I fitted mine I waited till the tank was nearly empty before starting then I believe I put an jack at one end of the tank (nearest the rear bumper I think)
Then manhandled the guard up the the boot holes nearest the front of the car. Slotted them in then it was a case of remove the jack and try to pin the tank up with one hand as I lifted the guard up to it.
Wedged them both in place with leg/elbow/shoulder and slotted the remaining two bolts in place.

Hope that helps
Chris
 
Mine was fitted by bolting it on top of the existing cradle straps. Do one side with an empty tank stays in place, offer up new guard and loosely bolt, removed bolts from other side, there is just enough space, and then you can fit the new guard on with the tank having fallen a little bit. Tricky but it works.
 
When I did mine the tank was half full, I propped it up just in case with some axle stands on concrete blocks. Fitting took less than 15 mins. I did have to use the trolley jack to push the tank back up to line up some of the bolts
 
bankz5152 said:
When I did mine the tank was half full, I propped it up just in case with some axle stands on concrete blocks. Fitting took less than 15 mins. I did have to use the trolley jack to push the tank back up to line up some of the bolts
Click to expand...
replaced mine with what looks to be identical. as previous run tank down. I then used jack to support while I removed all the bolts (4 off) I slowly lowered the jack to see if the tank would drop it didn't. so as soon as there was room I removed the old and used the jack to push the new guard into place. to make it easier I had to cut a small piece out to clear the tow bracket.
 
Just finished.
Thanks for your advice. It was, surprisingly, easier than I thought.
Had to modify the guard tho - don't they think you might have a tow hitch on an off road Disco?
All my bolts had been replaced, to ensure they wouldn't be seized.
Lucky I changed it - see pics of removed strap :eek:!

Pics of guard and mods
IMG_5478.JPG

Pic of old strap :eek:
IMG_5479.JPG

IMG_5480.JPG

Pic of finished job
IMG_5481.JPG
 
Last edited:
The Mad Hat Man said:
Just finished.
Will edit with pics in a short while when I have packed up. :).
Thanks for your advice. It was, surprisingly, easier than I thought.
Had to modify the guard tho - don't they think you might have a tow hitch on an off road Disco?
Lucky I changed it - see pics of removed strap :eek:!
Click to expand...
Likewise I was not looking forward to it. Stories of seized bolts tank dropping etc. However like you it was surprisingly straightforward. All nuts came off easy and tank stayed put. My cradle has rusted through one side and was resting on the arb.
 
pics now attached. :)

amazingly, although the tank was half full, i didn't need to support it. I was having kittens all the time i was under it tho :eek:.
 
The Mad Hat Man said:
pics now attached. :)

amazingly, although the tank was half full, i didn't need to support it. I was having kittens all the time i was under it tho :eek:.
Click to expand...
What gave me a bit of confidence was id heard how difficult it is to actually remove and refit the tank dur to its shape
 
i did put wedges through the bump stop brackets, but i aint sure if they would have actually stopped anything.
 
You must log in or register to reply here.

Similar threads

D
2010 90 Fuel Tank Guard Refit
Replies
12
Views
399
DefenderKeith
D
C
Fuel gauge reading
Replies
5
Views
536
tilly2
T
bluedog333
110 Fuel Tank Bolts
Replies
4
Views
692
miktdish
miktdish
MaxTheDog1
Freelander 1 Fuel tank cradle
Replies
18
Views
1K
andyfreelandy
andyfreelandy
Sieklo
Disco 2 TD5 Fuel line green fitting on the pump popping out
Replies
6
Views
1K
tilly2
T