My bargain genuine rubber mats finally arrived. Needed a clean though lol :D

DSC_0412_zps5jb48hmd.jpg


DSC_0413_zpsbjnyivev.jpg


DSC_0414_zpsimokcyfz.jpg
 
My bargain genuine rubber mats finally arrived. Needed a clean though lol :D

DSC_0412_zps5jb48hmd.jpg


DSC_0413_zpsbjnyivev.jpg


DSC_0414_zpsimokcyfz.jpg
Those were a good find. I bought a new aftermarket set a while ago, they were just some rubber matting with dots moulded in, cut to the same shape as Landy mats. They did the job OK but stank of rubber for months.
 
My parts car came with a set of genuine mats in great condition... but filthy and sticky gunk over them. Cleaned up great though. I got an aftermarket 'generic' rubber mat for the load space - pain in the butt not fitting properly.
 
Those were a good find. I bought a new aftermarket set a while ago, they were just some rubber matting with dots moulded in, cut to the same shape as Landy mats. They did the job OK but stank of rubber for months.

I always try and find genuine mats, fit is spot on. And they also jet wash off easy enough. These only cost me £20 Inc delivery. :D

My parts car came with a set of genuine mats in great condition... but filthy and sticky gunk over them. Cleaned up great though. I got an aftermarket 'generic' rubber mat for the load space - pain in the butt not fitting properly.

I still need one for the boot, but want to find a genuine one. I used industrial hand wipes to clean mine, also good for cleaning engine bays. And leave no residue. :D
 
Few little jobs done this afternoon. Adjusted my fog lights so I wasn't searching for planes lol
Checked all the wheel nut torques, Tyre pressures and if there was any rubbing from the bigger tyres (none found).

Fitted a map pocket on the rear door.

DSC_0415_zpswobkjqxh.jpg


DSC_0416_zpsvplszk69.jpg


DSC_0417_zps9mkj5gje.jpg


Fitted some smd bulbs into the interior lights, that I found in the garage. Will get some pics when dark later.

Load space

DSC_0419_zpssxzoxb1c.jpg


DSC_0418_zpsnrgyo3w8.jpg


Interior light

DSC_0421_zpsrizy4eai.jpg


DSC_0420_zpsh5cz0wyt.jpg
 
Couple of bits arrived today, leather steering wheel. Came up nice after a clean and Polish. :)

_20170127_190426_zps1h7yi5lf.jpg


And a parcel shelf, just need to dye it black. :)

DSC_0423_zpsl21xiyl9.jpg
 
That's an early wheel. The later facelift wheel has a mass damper to improve the feel of the steering.
 
Said all years in the listing, will it still fit? Can dampers be swapped over? And will the airbag fit?
Often the way with Ebay descriptions, but it will fit without a problem. The damper (gold coloured thing) is screwed to the wheel frame. So provided the mounts are threaded. The damper from your old wheel should swap over.
20170127_220950.jpg

I can't remember if the base facelift model wheel has the damper fitted. In which case, you'll not notice a difference. The damper does make the Freelander feel a bit more refined, by reducing vibration through the wheel.
The airbag will fit as they are all the same;)
 
Last edited:
My bargain genuine rubber mats finally arrived. Needed a clean though lol :D

DSC_0412_zps5jb48hmd.jpg


DSC_0413_zpsbjnyivev.jpg


DSC_0414_zpsimokcyfz.jpg
JC600. Nice motor. I fitted the elbow-rest onto my centre consul. Got it via Island 4x4. It's supposed to screwed onto the existing consul but I've found it sits there tightly enough without having to damage the existing one, (it's useful on long journeys but slightly inhibits some gear selection and hand brake application). I've also got wind shields fitted (Christmas present to self). They've survived the frosts but the front of my house is south facing and I'm not sure yet whether the sun might soften the glue on a hot day.
 
Often the way with Ebay descriptions, but it will fit without a problem. The damper (gold coloured thing) is screwed to the wheel frame. So provided the mounts are threaded. The damper from your old wheel should swap over.View attachment 116153
I can't remember if the base facelift model wheel has the damper fitted. In which case, you'll not notice a difference. The damper does make the Freelander feel a bit more refined, by reducing vibration through the wheel.
The airbag will fit as they are all the same;)

Cheers mate, I'm almost 100% certain we swapped that over on my old Freelander. They are self cutting screws that hold it in place, so was easy to swap. :)

JC600. Nice motor. I fitted the elbow-rest onto my centre consul. Got it via Island 4x4. It's supposed to screwed onto the existing consul but I've found it sits there tightly enough without having to damage the existing one, (it's useful on long journeys but slightly inhibits some gear selection and hand brake application). I've also got wind shields fitted (Christmas present to self). They've survived the frosts but the front of my house is south facing and I'm not sure yet whether the sun might soften the glue on a hot day.

Sounds good to me, glue should hold up. Had them on my old one for 3 1/2 years, and were still very secure. :)
 
Steering wheel fitted, damper swapped straight over. Screws are self cutting. :)

DSC_0426_zpsb0bz0tmb.jpg


Parcel shelf fitted, just need the proper brackets. :)

DSC_0425_zpshy3cfgtk.jpg
Nice job. Did you find some brackets for the parcel shelf yet? I have found something I am going to try as those brackets are ridiculously hard to obtain. I am surprised I haven't found a Chinese factory knocking some out; must be a demand
 
Nice job. Did you find some brackets for the parcel shelf yet? I have found something I am going to try as those brackets are ridiculously hard to obtain. I am surprised I haven't found a Chinese factory knocking some out; must be a demand

No, not yet.....probs just make my own. :)
 
No, not yet.....probs just make my own. :)
I am looking at the possibility of using something like wardrobe rail brackets, the flanged ends. I am not too worried about the boot space plastic trim as it's a bit battered there so if I can find something viable I am going to try it. I am going to get some pictures of mine on here when I give it a wash this week. I have some wind deflectors coming to put on first as well. I was considering the rubber body protector strip; have you considered it yourself? The single strip not the body kit which looks not good to me.
 

Similar threads