Co-Pang-Yang · Sep 21, 2011

Just realised that I need the trailer Saturday to scrap the Corrado.
So would need it back Friday night if your gonna borrow it.
Use of the engine crane is still ok though.

matthew2riches · Sep 21, 2011

wangie46 said:
Looking good there geof nowt wrong with the welding as long as ya got penetration you can grind the the rough looking welds down, well done mate

Matt not long now till we destroy your landy you looking forward to it?

I am really looking forward to it................ NOT

****in money has just disappeared. Had to take engine rubber mounts back and swap for brake pads so I hope engine mounts do not fall to bits as they're undone. Brakes have been metal on metal for god knows how long so I thought that'd be more important

I've even reconditioned the bump stops to save money

matthew2riches · Sep 21, 2011

Co-Pang-Yang said:
Just realised that I need the trailer Saturday to scrap the Corrado.
So would need it back Friday night if your gonna borrow it.
Use of the engine crane is still ok though.

That's all ok. We can drop chassis off at the workshop that we are at then bring it back to you Friday late night.

If the **** hits the fan and it still isn't back together by Sunday afternoon then I'll need to rob it again to get it all to the scrap yard

Discodad · Sep 21, 2011

Big Stu 12 said:
What you mean ****ed.......Yours is now in one piece again.......

Someone hinted you liked chopping up metel with a plasma cutter

It was a good job, until I hammerited it black

wickford90 said:
Got my first rock slider done, I know the welding aint that neat and maybe a bit burn here and there but a rub down and spray and should do the job. And yes Matt i did get penetration in the end, got half way through the welding and realized only had it on low power. **** taking will not be tolerated under any circumstance's.

Looking good there Geoff.

Mine is now booked for it mot on Tuesday. Next month Rach's car will need its doing and thats not looking good at all. Might be time to offload it.

Co-Pang-Yang · Sep 21, 2011

Ok Matt, we will figure something out I'm sure. Going out for a few hours Friday but I'll let you know when I'm due back and will make arrangements for bringing it back then.

Co-Pang-Yang · Sep 21, 2011

FOA Tusken. Didn't have my camera on me today but got a couple of pics on my phone for you:

Shot at 2011-09-21

One of two lol
Hope this helps.

matthew2riches · Sep 21, 2011

Co-Pang-Yang said:
Ok Matt, we will figure something out I'm sure. Going out for a few hours Friday but I'll let you know when I'm due back and will make arrangements for bringing it back then.

Did Stu phone you as he said he wants to collect it after work on Friday. We'll only want it for a few hours. Got to take the trailer to mine, get the chassis, take it to Battlesbridge then we can drop the trailer off anytime.

Cheers.

Big Stu 12 · Sep 21, 2011

Co-Pang-Yang said:
Ok Matt, we will figure something out I'm sure. Going out for a few hours Friday but I'll let you know when I'm due back and will make arrangements for bringing it back then.

Called Mike to arrange a time, his a bit behind on the borrowing of the Trailer, He says its he'll let me in to pick up, on friday, but can you let him know for sure that Matt is borrowing it, I'll then confirm the time with Mike,

Did try to call you about 1/2 hr a go mate but you must have been busy.... left a garbled message

wickford90 · Sep 21, 2011

matthew2riches said:
They don't look too bad mate

Did you mill the holes in the brackets?

No popped into the work shop on the farm for some scrap and found a 6mm piece with holes already in, result.

matthew2riches · Sep 21, 2011

wickford90 said:
No popped into the work shop on the farm for some scrap and found a 6mm piece with holes already in, result.

Sounds like you've got some luck on your side

Unlike me

Dirtneewbie · Sep 21, 2011

Evening All

matthew2riches · Sep 21, 2011

Dirtneewbie said:
Evening All

How many more times are you going to say that

We can see you are here, your green light is on

Dirtneewbie · Sep 21, 2011

iam in training to be a copper

matthew2riches · Sep 21, 2011

Dirtneewbie said:
iam in training to be a copper

A 3 meter length of 22mm by the sounds of it

Dirtneewbie · Sep 21, 2011

Any one seen Wheeler dealers where they done the disco and took it to some off road track with the rock n roll bridge?

matthew2riches · Sep 21, 2011

Dirtneewbie said:
Any one seen Wheeler dealers where they done the disco and took it to some off road track with the rock n roll bridge?

That show makes me laugh...... Hey Ed!! We've made £50

**** me :doh:

And the garage is far too tidy lol

djguy · Sep 21, 2011

Mmmm' wired new radio in to landy! When interior light comes on - radio goes off! When light goes off - radio comes on! Any ideas, the old radio worked ok, but it was held together with masking tape!

wickford90 · Sep 21, 2011

djguy said:
Mmmm' wired new radio in to landy! When interior light comes on - radio goes off! When light goes off - radio comes on! Any ideas, the old radio worked ok, but it was held together with masking tape!

Spooky!!!
by the way think I saw your old Disco at the Peterboro show _888 tel

Discodad · Sep 21, 2011

djguy said:
Mmmm' wired new radio in to landy! When interior light comes on - radio goes off! When light goes off - radio comes on! Any ideas, the old radio worked ok, but it was held together with masking tape!

Snigger.
Maybe i should turn my interior light on to get the front speakers working?

Dirtneewbie · Sep 21, 2011

could it be the masking tape

Well-Known Member

New Member

New Member

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Well-Known Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

Well-Known Member

Well-Known Member

New Member

Similar threads