Mr Noisy

Coming in your ears.
Hello

I need please:

4x front hubs from an old 90/110/defender

They are 10 spline items and are fitted to vehicles with AEU2522 cvs normally.

They are different to 200tdi disco hubs it turns out!!

No bearings required but any with good bearings in would be a bonus! :)

Please let me know.

Thanks!

P.s. Have disco hubs and various shafts if anyone wants to swap some stuff

Cheers !
 
Is it just the hubs you are after, I may have two off my '84 110, I'll look tomorrow mate:)
 
they were changed on a KA chassis but i didnt know if they were the same pre 87?

not very good on my early land rover history :D
 
they were changed on a KA chassis but i didnt know if they were the same pre 87?

not very good on my early land rover history :D

Do you know what was changed, cant see much difference in mine from 84 , I have 92/93 110 csw front axle on the 90 and I think all bits were interchangeable, drive shafts definitely were:)
 
Pretty sure that if it had AEU2522 CV and thick drive flanges then the hubs are correct

part number FRC6139

can always pop up if you think youve got a winner :)
 
I've got 3 10 spline shafts and CV's i can check mine for you mate but I'm not entirely sure what the differences are.

You'd have to send me a picture or explain what I'm looking for.
 
are they different to the hubs i gave you last year Sam?

well im buggered tim because if they were off your 90 they could have been right but tbh i think i would have noticed the difference, and i cant honestly remember if you gave me just hubs or hubs and stub axles etc

when i remember building your axle up, that was the same as 200tdi disco from what i remember so i think perhaps it was either a very late defender axle or it was a disco axle, but i cant properly remember

either way i ended up with about 16 hubs at one point so i had a mass weigh in, but as far as i can remember they were all disco type

too late now though! :p
 
well im buggered tim because if they were off your 90 they could have been right but tbh i think i would have noticed the difference, and i cant honestly remember if you gave me just hubs or hubs and stub axles etc

when i remember building your axle up, that was the same as 200tdi disco from what i remember so i think perhaps it was either a very late defender axle or it was a disco axle, but i cant properly remember

either way i ended up with about 16 hubs at one point so i had a mass weigh in, but as far as i can remember they were all disco type

too late now though! :p
i only ask as ive still got the rears
 
this is early 90



this is 200 disco (and perhaps some defender but cant say for sure)



note the deep plastic cap over early 90 drive member with thick drive member

note the stub shaft setup with built in drive flange on 200 disco
 
the 90 that had these up front had drums on the back

if your 90 had discs on the back maybe someone fitted disco axles because tbh all my spares were disco and any stuff we used on yours must have been disco aswell!
 
the stub axles where different also, mine had the longer of the two in the picture
 

Attachments

  • 053.JPG
    053.JPG
    274.3 KB · Views: 143
I've got 3 10 spline shafts and CV's i can check mine for you mate but I'm not entirely sure what the differences are.

You'd have to send me a picture or explain what I'm looking for.

maybe the diagrams will help matt, do you have hubs or just shafts and CVs?

cheers :)
 
the 90 that had these up front had drums on the back

if your 90 had discs on the back maybe someone fitted disco axles because tbh all my spares were disco and any stuff we used on yours must have been disco aswell!
could well be sam, just thought i may have some use full parts laying about
 

Similar threads