mud muppet · Jun 7, 2013

Bought a 200 disco a while back.its got a lft on it 3" I think.

Handling has always been bad.
Someone said get some plus 3 radious arms and maybe bushes had gone on pan rod arm.
So replaced with the said bits and still drives the same.do you think an adjustable pan rod might be the way?

matthew2riches · Jun 7, 2013

I am having the whole "crabbing" issue at the moment as well. Would be good to know how it is solved.

Jamie1987 · Jun 7, 2013

Have the wheels been spaced out at all? I heard for every inch you go up in height you need to go out an inch in width.

Being that high screws with its centre of gravity.

mud muppet · Jun 7, 2013

Wheels have massive offset.Got 35/13,50 mudz on.But it did it with 265s on from before.....so......duno

wiltshire landyman · Jun 7, 2013

I got 2" lift 2" body lift..37" mudzillas and mine drives fine..standard props,standard arms etc..

you must have some other worn out parts somewhere

robint · Jun 7, 2013

could be as simple as warn out steering box

Pikey · Jun 7, 2013

Check wheel bearings and all bushes.

mud muppet · Jun 7, 2013

Think will start with pan rod arm.Either cut it and drive it up an down see if gap is wider.Then could either put tube over both ends and weld up.

mud muppet · Jun 7, 2013

Bearings are all good and bushes

wiltshire landyman · Jun 7, 2013

mud muppet said:
Think will start with pan rod arm.Either cut it and drive it up an down see if gap is wider.Then could either put tube over both ends and weld up.

that's pointless it will make no difference

mud muppet · Jun 7, 2013

So would you say put an adjustable pan rod arm on?

fanatic · Jun 7, 2013

Bushes
Steering damper
Swivel hub preload are main **** handling issues-and I dont like lift kits much

wiltshire landyman · Jun 7, 2013

mud muppet said:
So would you say put an adjustable pan rod arm on?

nope trying to set them up will cause you more grief..

its gonna be summit simple that you've overlooked..have u looked at track rod ends to see if there worn out?

mud muppet · Jun 7, 2013

wouldnt the mot picked up on track rod arms?

craigyb · Jun 8, 2013

mud muppet said:
wouldnt the mot picked up on track rod arms?

Depends who's mot'd it

discomark10 · Jun 8, 2013

Would be usefull to get more info on the handling issues...
Crabbing (mentioned above)
vague steering
wanders around
too light steering
too much roll

mud muppet · Jun 8, 2013

have a chat to very nice man at the garage Tuesday,see if he will have a look.been out in it today think rear wheel bearing is busted.rattle noise when going along and the hub is getting hot to touch.

chriswall0 · Jun 8, 2013

Might be a bit obvious but what about ball joints? I've just changed mine on my fender sorted my problems right out

mud muppet · Jun 8, 2013

think the rear hub is shot.just went out to move it and pudle of black stuff on floor and coming from inside of rear axel by tyre:frusty:think I`d be rich if I hadn`t got a landy....

wiltshire landyman · Jun 9, 2013

so not the steering atall then:doh:

New Member

New Member

New Member

New Member

I’m back

Well-Known Member

Dummy Ejection Facilitator..

New Member

New Member

I’m back

New Member

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

I’m back

New Member

New Member

Well-Known Member

New Member

New Member

New Member

I’m back

Similar threads