damian46

damian46

Gammon-in-chief
I bought a set of new front brake discs for my 2005 freelander td4 also received a set of pads for free problem is the caliper won't go back over the pads
Removed bottom bolt flipped caliper up Removed old pads pushed piston back in ,cleaned up ect they fit on caliper carrier fine the caliper just won't go back down over the pads
I've put the part number on the box In Google search and comes up with freelander 2000/2006 any ideas appreciated
 
Ok just so I'm reading this right, everything fits together ok but the pads won't fit back over the new discs.

Do you mean the pads are too thick ie there isn't enough space?
 
looking at this video both bolts are removed, and the piston wound all the way back. The slide pins, behind the rubber cover, comes out and needs greasing every time or it'll seize. May need a clean up if rusted.
Obviously, as in the video, super clean overalls required and super clean work area! Also pre-loosened bolts are a must.
 
No not too thick the pads fit were there supposed to go it's the caliper itself it won't go down enough to fit the bottom slider pin bolt back on to the carrier I think the radius on the pads are too big (the metal part that curves) I will investigate more today
 
J_D said:
looking at this video both bolts are removed, and the piston wound all the way back. The slide pins, behind the rubber cover, comes out and needs greasing every time or it'll seize. May need a clean up if rusted.
Obviously, as in the video, super clean overalls required and super clean work area! Also pre-loosened bolts are a must.
Click to expand...
Just watched the video cheers on most of my other vehicles pajero ect I've always removed the bottom bolt and pushed the caliper upwards to clear pad then just removed old ones clean up and grease pins drop caliper back down done, so I will remove top bolt and see if that works, will wash overalls first😆
 
  • Like
Reactions: J_D
Not sure this will apply to you but on a Freelander I was putting pads in I found out why they did not fit was because it had one old calliper ( for the solid disc) not enough room for the pads
 
Dar ran Dar ran said:
Not sure this will apply to you but on a Freelander I was putting pads in I found out why they did not fit was because it had one old calliper ( for the solid disc) not enough room for the pads
Click to expand...
I've ordered 2 new calipers so once they arrive I will get on with the job again ,
 
First ones are the old style right ones are the correct ones
 

Attachments

  • IMG_9206.png
    IMG_9206.png
    921.7 KB · Views: 79
  • IMG_9207.png
    IMG_9207.png
    1.5 MB · Views: 81
Did you just try and undo the top caliper bolt and lower it then ?
 
Last edited:
I've had plenty of pads that don't quite fit right. Usually it's a case of filing the metal backing slightly at top & bottom so they slot in properly.
 
pwood999 said:
I've had plenty of pads that don't quite fit right. Usually it's a case of filing the metal backing slightly at top & bottom so they slot in properly.
Click to expand...
They slot in properly its the caliper that won't drop back over the new pads
 
You must log in or register to reply here.

Similar threads

T
Hi all newbie here
Replies
11
Views
729
andyfreelandy
andyfreelandy
T
Complete newbie here
Replies
5
Views
626
brianp38dse
brianp38dse
M
Freelander 1 Brake Piston Rewind Tool
Replies
13
Views
2K
mbrokof
M
DefendingLancashire
300TDI Four-parter: brake wear, lift pump / fuel filter, turbo, and bushes / squeaking
Replies
13
Views
472
miktdish
miktdish
Badger688
Brakes??
Replies
9
Views
2K
Anaconda
A