Intestinalworm

Intestinalworm

Well-Known Member
Underestimated batteries until fairly recently - last couple of years I have had a run of battery issues with different vehicles. Was worthwhile re-investing in a DMM!

Okay, put a new battery in the D2 Td5 just several weeks ago! Perfect starts and no issues. However, I checked (just out of interest) the voltage output with my DMM today:
12.3V static and 13.9V engine running
Static voltage appears low!?
Should I charge the battery?
Thing is, my battery charger is a hand-me-down and it is very basic, it's what I now understand to be a trickle-charge battery; I understand these are not suitable for charging "flat" batteries.
Any thoughts?
 
14v when running is usually the norm, that's the charge voltage most see and indicates a good alternator.
Anything at or slightly above 12v when not running sounds perfect for a 12v battery.
I was always told the slower you charge a battery the better. Trickle charging therefore seems to fit the bill.

When was your DMM last calibrated? Check it against another then you know whether your readings are accurate or not.
 
Car batteries provide 12.6V DC (direct current) through six cells, producing 2.1V each.
~12.6V: fully charged
~12.4V: 75% charge
~12.2V: 50%
~12V: 25%
11.9V and below: effectively zero charge.

Therefore go for a half hour drive if you want a fully charged battery,
My disco is only used once weekends twice a month just to keep it in running order, so the battery is below 12v sometimes, but the engine turns over 4 times and starts ok, on my return, my ‘certified’ multimeter shows the battery at 12.6v, alternator charging between 14.1 - 14.5v when under load, so no issues there either.

If you thinking of getting a maintenance charger the have a look at C-tek’s products, never had any issues with my 20 year old C-tek XMS3600 which is connected most of the year to my classic car, and for other cars then the future proof XMS 5.0 is used, which I understand will recondition a very dead battery.
 
kermit_rr said:
Ok I'll bite.
How can you check the battery out the car it's locked and the bonnet is closed? Leaving the bonnet on the first catch seems easiest
Click to expand...
You cant. But with can after installing a wire from each battery terminal out of the engine bay to a external weather proof remote socket. So when u need to test the battery just remove the protective cover to expose the remote pos & neg terminals. Install a suitable socket and charge the battery as well if required.
Similar in principle to the neilly suggestion with the S trailer socket in post #6.

Or use a gizmo from eBay to check via Bluetooth on your mobile.
 

Attachments

  • AB0A00E2-A46A-4879-85E0-8D7727234375.jpeg
    AB0A00E2-A46A-4879-85E0-8D7727234375.jpeg
    290.6 KB · Views: 120
Two bits of thin wire so no tit can cause a fire, two low amp fuses at battery end of wires, wires out front/side of bonnet, job done.
Or even simpler tape bonnet switch down?
Probably others, but i have used the first one before.

I have since gone one step further and fitted an anderson plug, again with a fuse in case someone tries to get cute by shorting the terminals together.
 
+1 on the mxs5
https://www.ctek.com/uk/products/car/mxs-5-0-uk
I had a golf layed up for 15 month , in that time as voltage dropped about 4 times I started up and ran for 30 mins at high tickover , it wasn’t enough to get a full charge back
I eventually let it go too flat and thought new battery was required , start stop AGM batteries very exp
So bought the CTEK , it has recondition modes to desulphate the lead plates , car on road now and batt seems fine
12.3 is low so fully charge up and see if it holds charge as said above,
 
discool said:
You cant. But with can after installing a wire from each battery terminal out of the engine bay to a external weather proof remote socket. So when u need to test the battery just remove the protective cover to expose the remote pos & neg terminals. Install a suitable socket and charge the battery as well if required.
Similar in principle to the neilly suggestion with the S trailer socket in post #6.

Or use a gizmo from eBay to check via Bluetooth on your mobile.
Click to expand...
Yeah yeah, blah blah, "just fit this flipping gizmo".:rolleyes::rolleyes::rolleyes:

Just leave the bonnet up with a weight holding the bonnet switch down.:)
 
lynall said:
Or even simpler tape bonnet switch down?
Click to expand...
ABSOLUTELY, why over complicate stuff. He wants to get his car going, not frig around with it while it still isn't going?
Or, guess what, take the batt, off the car, charge it than test it properly.
It ain't rocket science!!!
 
Stanleysteamer said:
ABSOLUTELY, why over complicate stuff. He wants to get his car going, not frig around with it while it still isn't going?
Or, guess what, take the batt, off the car, charge it than test it properly.
It ain't rocket science!!!
Click to expand...

Could be an issues if car is left roadside, sadly not everyone has off road parking.
 
You must log in or register to reply here.

Similar threads

P38Seb
P38A Battery Du Jour
2
Replies
24
Views
2K
Grrrrrr
Grrrrrr
Roverdrive
L322 L322 Battery strangeness
Replies
16
Views
1K
kermit_rr
kermit_rr
S
Freelander 2 cranks but wont start - intermittently
Replies
7
Views
2K
Freddie17
Freddie17
L
D2 REMOTE NOT WORKING - CAN THE RF RECEIVER BE TESTED??
Replies
8
Views
2K
Stanleysteamer
Stanleysteamer
Blob
L322 (Not your usual) battery drain
Replies
7
Views
2K
Datatek
Datatek