Thanks Matey I have pulled it out of the landy tonight and i am planning to look at it at work tomorrow as i had another boring day planned

If you have the mic socket pinouts they would be handy Thank you so much for all the help..

Thank you i would take a copy of any information you have, and there is no rush we are currently using portable radios it will just be good to get the CBs working eventually. Thanks for all the help, i am going to go home tonight and rig an earth up to the antenna and see what happens..

Thank you Would it be this that is causing the lack of white noise?

Thank you for all the help, i have the 5-pin mic. i have been searching the Internet for help and circuit diagrams etc (i dint believe they exist), and i have found i may have made a school boy error. I will explain this from a distance so anything hurled at me is less likely to hurt...

Hi all me and a mate bought a pair of Midland 77-099 from a well know auction site, it said that they were both in working order if not a little bit worn.. So we set about and fitted them into our Discos to be used whilst out and about green laneing etc. My set-up is as follows: Unit up in the...

Hi all i have found that my front prop shaft UJ is dead on the transfer end, the casting that bolts to the transfer box is damaged so i need to replace that. I have one from a series 2a that looks the same dose anyone know if it is? Also the splinded part of the prop shaft should that side...

Hi I have read and been told that p38 seats will fit straight into a disco 1, so off I went and bought the wife a nice leather interior from a p38 and they arrived today. I can't see how they just fit in the rear seats locking mechanism is in a totally different place it is the standard u...

Hi all I have a knocking comming from the front end when i take my foot off the power, i raised the front wheels and rocked them at 12 and 6, the ns had play and the os was tight. I have got a swivel joint kit which has: 2 bearings upper and lower pins a selection of gaskets do i need...

I have just read that the sound could be caused by a faulty o-ring on the oil sucktion deceive in the sump slowing air into the oil, we have replaced the ladder rail so we did remove this, could it be this?

No we were really careful, I am concerned now as we have been really careful when re-building it it sounds like a tappets rattle you would get on a diesel,

I checked the liners because I know they can drop and they were fine would they still move?

Hi all I have just replace the cylinder head gasket on my 2003 1.8freelander, I started it up and there is a nocking noise coming from the engine it seems worst from the top right by the oil filler cap. I had the head skimmed and the cams were both removed and cleaned, could it be any of the...

I couldn't feel any up or down just the rotational play through the transfer box.

Hi All I have a 300TDi on a M plate, it drives fine but when i take my foot off the accelerator it vibrates (the whole front end), i laid under it today and looked for loose or worn joints and found the track rod could be rotated slightly. I also found the front prop rotated approximately 45 deg...

Thats what i need to check how do i set the two cam sprokets after a complete strip down of both cam shafts?

My brother has got a 2001 freelander 1.8 and the head gasket has failed, he has stripped it down and we sent the head away for skimming. The engineering firm stripped the cams and now i need to reset the timing, we are not sure which cam went where so i am now at a loss as to how to re set the...

i have been told that a P38 interior will fit..

I am looking to fit a new interior into my 95 300tdi will a disco 2 interior fit? I am looking at things like door cards seats etc. Rob

Hi all I am currently working on a 95 300tdi for my wife and want to put some modifications on it that will make life bait easier. At the moment the disco only has driver door central lock and I would like to make it remote, I have found loads of kits on the internet but would like to know if...