Ordered. Take a week or so to arrive and will update on progress. Thanks.

Getting there guys but still not perfect. I would say its warm rather than hot. Have tried the 2000 rev bleeding trick with the bleed valve cracked open several times. Have also replaced the pressure cap. The pump is working fine because with the bleed valve removed water will bounce off...

Had key problems with my mgf and obtained a apare key with a little device that you plugged in and it programmed the key. All good. Then that prompted myself to obtain the eka code for my disco 2. Two working keys but no eka. Rang up the local dealers and for exchange of my reg number i was...

Thanks guys. Very nearly there. Front raised on ramps. Stick from the seat to pedal to hold on 2000 revs, bleed screw cracked a bit and as a trickle of water came out from the hose , topped up the expansion tank. Did this for approx 10 mins until warm and the heater was deffinetly improved. Not...

Thanks guys. Let you know how i get on.

When you say hope its valve not stuck are you referring to by pass valve in the thermostat or cap.? Sorry but may have got myself confused.

Thanks all. Will be trying tomorrow.

Thanks. Will give it a try. Dont think theres a lot wrong just a knack to get it right. Thanks

Need help guys and gals. Had to change my thermostat 3 to 4 weeks ago because of water leak between it and hose. All seemed good and with lock down and other vehicles not used much. Now With colder weather noticed that heater not seemed to be working. So checked thermostat in right way round...

Go for a spin last night to help put the father in law to bed who has Parkinsons. Depending on wether its a good or bad day sometimes have to do the 20 mile round trip to help mother in law. Anyway. Decided to slide the seat back half an inch. Yep. SRS light on. Had fixed proplem on passenger...

Probably not too much to worry about then. Thanks for assisting.

Right have managed to get some readings. The gauge had a reading of 61.1 (with the meter set to 200) Managed to take a check reading off a series 3 gauge , which to to be honest think mine is as well and that was 60. So basically the same. Checked the sender cold. Had no reading...

Thanks. Just got in from the garage trying to extract my mgf starter motor from the depths of the engine bay, and read this. Thanks that would be very useful. Will be out there tomorrow and will check. Just to double check on the sender as electrics not my best thing will check between the...

Instruments have been swapped several times. When i got it it was sporting a series 3 bulkhead and series 3 guages. I have swapped back to original series 2a dash and gauges of unknown origin. Thanks trying to identify.

Heres a photo of my gauge. Not sure which landy type it was originally off. Any body got any idea ?

Suspected as much. Think i will post a picture of my gauge and see if its origins can be established. Not sure whats it off.

Meant to say that ever since i finished spending 3 years restoring in the spring. It was diesel but now back to original petrol. But most bits swapped in or out.

In a seperate thread i have started the Cronicles of my 2a but i have a problem with my temp guage. It rises to just below the red. Sometimes just into but mostly just below. Does not seem excessively hot. It has a new sender and replacement instruments over the years. The regulator is new...

Dont mind you asking. I was chatting to Tom of Adventure Tours in the middle of the plain after i had rearranged my original front bumber , and how my tow bar acted as a plough, and discussing improvments that could be made, when he mentioned he had a 2nd hand one one knocking round his...

Rear Bumber now on as well as Tow bar and tow eye . The drop plate and ball hitch can be swapped in as required. New shocks and drop links fitted. To be honest bit disappointed with the drop links as the nuts were obviously mismatched and had to work 3 of them up and down in the vice to...