Hi mate yes every thing nice and clean but will recheck power supply at unit etc when I refit nothing seems untoward so far, raining today but going to refit unit tomorrow and start rechecking everything, have a nagging feeling I may have diagnosed the wrong module being honest with you, at...

Oh dear no fault found back to drawing board?

As suggested re-downloaded ap200 app on my phone, used wifes before as it was newer model, low and behold calibration works, so tried to go through instructions, threw up c1a00-54 control module, put this down to me messing with the ride height so had a cup of tea tried again this time worked...

Never thought of that will re install, pretty sure I have gotten all my suspension info from you mate, will fiddle with it futher this afternoon, yes shame you don't live round the corner although I might be a pain Lol, can always get mate from garage to calibrate, doing pre mot work/check on a...

Sorry got cut off, still to run live data, keen to work out issue rather than throw parts at it, once suspension issues resolved most likely will sell it keep the auto, couldn't calibrate with autel this morning in touch with help desk, I have most likely done something wrong when registering I...

Yes mate not much left, getting there no lights so is on the mend I hope, what confuses me is yesterday i only changed the compressor basically 2 off one on, as you know only one hp pipe which wasn't leaking any way last night suspension stayed up perfectly, s

Changed compressor yesterday found leaks on the one I had fitted had corrosion, so, changed to one I had from a 06 fitted new dryer beads o rings etc fitted took for drive amber light pops back on, pressure to low code, so "borrowed" compressor from one I've just rebuilt, used last night no...

Landrovers together in front yard still have under trays and wheel arch liners/trim to fit, discs/pads and have a leak off pipe leak to do, abs off to ecutesting.com for repair will bleed and do brakes on its return with ap200. Back on 07 tomorrow have ordered a new reservoir block, and going to...

Messing about with last few jobs before moving it out of the workshop, autobox arm to cable had seized so stripped cleaned and soaked in oil for a bit works fine now, had a power steering issue but seems to have resolved itself think it must have had an air lock, no puddles underneath and it...

Thanks mate yes took me a while but just found it on d3 website vdcm and abs same thing, think its coded, but not sure, only codes I couldn't clear was vdcm, your help with resistance tests confirmed continuity from abs to wheel sensors, and can bus link was ok so was starting to suspect abs...

Thanks mate changed rear valve this morning compressor ran for a while, then the fickle finger of fate happened, my friend from the local garage turned up needing a 2.7 injector so we did a Norfolk barter, he agreed to come back with his diagnostics, he turned up about an hour ago, blew up the...

Yes thanks mate canbus seems intact will check further, canbus wires are spiraling in the loom?. motor runs sweet, locked in park, still needs 3L transmission fluid, no suspension now has some pressure in bags lifted slightly then compressor cut out warning back on dash, can't make sense of...

Fitted new speed sensors, bought a new ohm meter, reconnected battery this morning started up runs well on the button, but then it happened dashboard lights up like its Christmas again, big F loads of different codes tried ohm readings from abs pins to sensor's r/l 1.080m r/r 1.065m fronts with...

Bit of a result only one light left on dash and two codes which are temporary, haven't had time to put the wheels on yet, hoping to raise suspension, cycle gears and fill the trans with it's remaining 3 litres, and at least move it remaining hopefull, as want to get the xf in, undertrays and...

So instrument cluster and abs are the ends of the loop, now I know the pin numbers will test sensor harness for continuity abs plug to sensor at some point and possibly clean the rear hubs too many thanks for your help will keep you posted

Thanks mate just what I was looking for your a star will help me get my head round it, already sust that sensor supply and signal go to the abs so can now check continuity, plug to abs will work through issues over next few days, sensors arrived but couldn't fit them into such a rusty place so...

Sorry ment to say can you reccomend a breakout box something else I would like to learn about many thanks for all you help and advice waiting for sensors today and rear valve block tomorrow many thanks mate

You always help in a big way mate, many thanks. Front sensors read 01.1 on 200m setting, but on 2000 settings reads 489 but the damaged one flashes to 1650 then goes blank?, all readings otherwise the exact same on other three sensors on both settings will let you know readings on new ones be a...

Hi mate waiting for new speed sensors before scanning again ap200 is spot on thanks for the heads up, where I'm at, found a bare wire on r/h sensor, ordered new fronts also want to check the ohm reading of a new ones arrive today, rear valve still on until new arrives, old one is constantly...

Yes abs unit and valve block's only at this point suspected and concentrated on, waiting for a rear vb before removal