Surely should be same part both sides ? Just make sure you get the correct thread size & connector type.

err . . actually three causes. 1. Its either that the valve is actually stuck closed. 2. Or its a faulty height sensor & ECU confuses the reason 3. Or intermittent connection in the driver pack connector, i.e. if the driver pack cannot trigger...

Prop off is easy, even on axle stands, but do the one-wheel test first !!

@nevillen Microcat finds the VIN. Search driveshaft part number using that ?

Do they make the roof spikey ??

The "approximately a year old" comment from the seller probably means someone cleaned the battery to make it look newer !! +1 do the simple overnight voltage check above with the battery disconnected. Also getting Halfords to check its...

@James Brake as others have said rebuild or replace with another 1.8 is the easiest approach. Then sort the IRD & Prop, etc. A donor car would help you a lot & potentially provide many bits you're gonna need or break off-road. Also this forum...

Ignored as requested.

ok I stand corrected. I do wonder how it would behave if the disco sensors did provide pulses, especially if the front & rerar rate per revolution were different ? I guess the ABS/TCS would treat it as spinning or slipping wheels - a bit...

Essentially it’s getting the preload on the lifters correct. If it’s wrong it impact compression & engine won’t be at its best.

You could search the forum or google it. It’s been described many times by peeps changing cams, lifters or doing head skim.

And what is the difference ?

Wrong number of pulses would make the speedo wrong, plus front & rear wheel mismatch. ABS fault implies the sensor cannot see the reluctor. Definitely. Supplier might have swapped them for P38 version if they were unused, but probably not...

Check the connector underneath the valve block. The connector body may appear tight, but the socket contacts open up slightly over time due to heat & cold cycles in the engine bay. Intermittent connections will cause "valve stuck" faults when...

Just to add to this, if the engine is on 122000 do the basics before anything like ECU mods, i.e. Replace main & big end bearings, piston rings, etc. Clean up & relap the valves. Look at a mild tune cam (which should not require ECU mods)...

@petebowling when posting a thread, at least select s suitable car model prefix. Makes our crystal ball gazing a little easier.

Most cars use signals from ABS for the speedo.

Does anyone know what resistance I should get across the rail sensor terminals ? Our old sensor measures about 130Kohm across the two outer terminals. The new replacement we got from eBay measures >> 3Mohm which seems wrong. I still get...

Headliner map pocket formers. Helps get the headlining properly into the recess. If anyone wants these they are going free. Either collection in Langley, or you pay postage.

[Edited] Was I'm getting the same P1190 fault on my son's 2004 TD4 Auto at high load. Previously the car was smoking a lot all the time , even at tickover so did this lot. Cleaned injectors. EGR bypass fitted plus cleaned out turbo pipes &...

You have already changed plugs & leads, but try the coils flip anyway. Then clean get a DIY injector cleaning kit & clean the injectors. It's quite easy & that way you will know if one is bad. If you had a location (town name) someone...

Which ECU is fitted ?? Unless someone has messed with the wiring, it should not be possible to fit the wrong type. Also are you using the correct Nanocom menu ? TRW MPS (TYPE 1) TRW SPS (TYPE 1)

Fired up the green P38 for the first time in several weeks. EAS went straight up to correct height. Loaded up some garage rubbish, cardboard, an old freezer & load of empty beer cans, and off to local household waste centre. What bugs me is...

It needs old fashioned engine basics rather the repeated diagnostics, i.e. Clean or better still replace spark plugs Test injector spray pattern & clean them. It's easy DIY using a kit like this https://ebay.us/m/cNgk6I Compression check all...

You need to check the fuel pressure to at least rule it out. Diags can read them.

According to Mark_C on rr.net L322 section, all the immobiliser does is prevent the key turning & starter engaging. If that's true then sort the fuelling first !! https://www.rangerovers.net/posts/2209790/ But other threads say it stops...

Thanks Andy. In that case it will be sold as a 2wd !!

They probably make more money doing immobiliser stuff than fuel regulators & pumps !! Fuel pressure codes are just a clue something is wrong. The diagnostic should also show the actual pressure values.

No they are supposed to be illuminated like all the P38 switches.

Yes I thought it seemed a little tight. I did read somewhere that after sitting for a while, they need at least one full revolution to distribute the fluid before testing. This one has sat on the bench in my garage for at least 6 months. It...