gaz18

gaz18

Member
Hi all iv just sand blasted my defenders chasies i was wondering what is the best think to coat it with thanks
 
here's me thinking he'd put a chaise longue in ... would make a change from red brake calipers i suppose
 
Aye, & give him sumat to throw himself onto when it all gets too much & he's stricken with an attack of the vapours.
 
stripped mine and then painted it with Temaprime, a galv rich paint used for exposed steel etc

chassis_paint_3-01.jpg


Then after getting to this stage...

chassis_paint_2-01.jpg


I then sprayed it over with Gravelguard , a tough textured flexible finish....

chassis_2.JPG


Even removed and did the fuel tank etc as its such a bad mud trap...

fuel_tank.JPG


Did the footwells and anything else that stayed in one place for too long :)

footwell_ps.JPG


Hopefully the damn thing should last a year or two now :)

I did a previous chassis with hammerite.... what a terrible mistake, we have a lot of flint / stone lanes around here..

The hammerite chipped and came off leaving the chassis exposed in lots of places... looked superb before i seriously off roaded and laned it... however Id never use it again... however that is just my personal experience due to the conditions around here...

Cheers Steve
 
ebbadger said:
I did a previous chassis with hammerite.... what a terrible mistake, we have a lot of flint / stone lanes around here..

The hammerite chipped and came off leaving the chassis exposed in lots of places... looked superb before i seriously off roaded and laned it... however Id never use it again... however that is just my personal experience due to the conditions around here...

Cheers Steve
Click to expand...

That's why stage 2 on my chassis is a libral coating of waxoyl.
 
buttonmonkey said:
That's why stage 2 on my chassis is a libral coating of waxoyl.
Click to expand...

yep did that but although waxoyl is good it wont creep and cover a 10p sized chip when on the outside, good inside the chassis though as long as you warm it a little to ensure a good coat on all four surfaces when spraying ... a bit easier than rolling the landy over to get a good internal coat :) as I said just personal experience with the lanes round ere but i will never again touch it with a barge pole... overpriced... and overated

as for the gravelguard.. six months and a lot of serious abuse and its not even marked.... mud doesnt stick to it very easily which is a bonus.. washes off really easy.... and it was a lot less than what my hammerited rangey chassis cost.. compressor and a schutz gun gets in every nook cranny n pinhole perfectly...... much better than brushing as brushes are difficult to get into tight spots n pinholes...

Cheers Steve
 
ebbadger said:
as for the gravelguard.. six months and a lot of serious abuse and its not even marked.... mud doesnt stick to it very easily which is a bonus.. washes off really easy.... and it was a lot less than what my hammerited rangey chassis cost.. compressor and a schutz gun gets in every nook cranny n pinhole perfectly...... much better than brushing as brushes are difficult to get into tight spots n pinholes...

Cheers Steve
Click to expand...

Well as mine is still a rolling chassis for another week or so looks like I may have to go get some gravelguard and give it a once over then.
 
You must log in or register to reply here.

Similar threads

Dayo97
Battery box paint
Replies
5
Views
450
dag019
dag019
rich28uk
L322 Brake damper weight
Replies
14
Views
799
rich28uk
rich28uk
R
Spraying and nisocoat 2
Replies
0
Views
731
resto_d1
R
andde
Off road rims + tires size without lift kit
Replies
3
Views
279
andde
andde
S
Lt230 1.310 ratio
Replies
3
Views
233
Sam Warder
S