drewster
Well-Known Member
I thought something was odd with your car now I know its a steam engine
ratty
I'm not special I'm limited edition
Dr No
Active Member
Gratuitous pic -
Gratuitous or not very nice.
big si
Well-Known Member
Pulled lump out ready for crank seal, got interior light and dash lights working, heater working, reverse light working, fitted thermal fan and switch , stereo fitted, got cb working,wipers working. Got to fit crank seal and refit engine then do head gasket and refit dash and she's ready for the chippy run. I'm fookin knackered
Freelaner
Landy Driver
Pulled lump out ready for crank seal, got interior light and dash lights working, heater working, reverse light working, fitted thermal fan and switch , stereo fitted, got cb working,wipers working. Got to fit crank seal and refit engine then do head gasket and refit dash and she's ready for the chippy run. I'm fookin knackered
yer did all that at work
Drove it carefully as the swivel bearings are very loose.
Got the parts at 17.10 this evening so too late to start but tomorrow i'll be having a go at fitting swivel repair kit and new disc, pads, brake pipe and braided hose to near side front of Disco and just repair kit and braided hose to offside as that has new disc and pads on it already
Got inner hub seals for rear as well but think thats goin to be done Friday.
Got the parts at 17.10 this evening so too late to start but tomorrow i'll be having a go at fitting swivel repair kit and new disc, pads, brake pipe and braided hose to near side front of Disco and just repair kit and braided hose to offside as that has new disc and pads on it already
Got inner hub seals for rear as well but think thats goin to be done Friday.
Dr No
Active Member
Drove it carefully as the swivel bearings are very loose.
Got the parts at 17.10 this evening so too late to start but tomorrow i'll be having a go at fitting swivel repair kit and new disc, pads, brake pipe and braided hose to near side front of Disco and just repair kit and braided hose to offside as that has new disc and pads on it already
Got inner hub seals for rear as well but think thats goin to be done Friday.
I am doing much the same without the brake bits though. good luck.......You as full of trepidation as me?
gemsdad
NOT BOTHERED.
Silverlandy
3.5efi's other half
Drove down to Braintree today, left in plenty o'time and managed 125mile round trip on quarter of a tank...really getting into Radio2 now for two reasons, firstly I'm getting old and secondly I have bought a plug in iPhone/**** nav charger and it interferes with KissFM a buggery. R2 is fine though
Dr No
Active Member
Stripped the O/S front swivel joint. I'm glad i have an angle grinder, those stupid torx screw heads in the bottom bearing had to be cut through. as did the surrounding metal work. The other bolts were so rusted up i had to use the two spanner 'flat pry bar' method of getting them undone. Now I ain't showing off by saying I used to bench 165kg as a training weight (Fat and old now admittedly). But, I swear it took every ounce I had to get some of them cracked.
Inside the housing everything was mangled. Bottom and top races were in bits, swarf and shards of metal everywhere. Complete rebuild this weekend. Might as well do Calipers and Discs whilst I am at it.
Inside the housing everything was mangled. Bottom and top races were in bits, swarf and shards of metal everywhere. Complete rebuild this weekend. Might as well do Calipers and Discs whilst I am at it.
Grahame of the shires
Active Member
Done nothing in Keith, (my Discovery, Don't ask about the name) because the wifie nicked it. Almost called the cops but thought better of it!!!!
discostew38
Active Member
Fitted the new fog light and re-aligned the front bumper
