Cleaned my injectors with my wife's ultrasonic cleaning thing just need to get it back in the house without the boss knowing. Seems to of done a good job
 
Removed the rear prop, replaced it the right way round minus the spacer and it all looks better than when it was wrong .. ;)

Fettled me eggsauce, it's been rubbing on the A-frame since .. er .. a long while ago. Big 'ammer, long lever and a hacksaw and it now doesn't vibrate any more. Replaced a drag-link track-rod end, wing panel indicator, and just went round checking bolts etc .. which was good 'cos the offside spring retaining bolts were loose, I guess the plate has bent .. might sort some thicker steel for them later.

Tomorrow I'll check the wheel bearings again, all the oils and just fettle stuff .. ;)
 
Paul D said:
Removed the rear prop, replaced it the right way round minus the spacer and it all looks better than when it was wrong .. ;)

Fettled me eggsauce, it's been rubbing on the A-frame since .. er .. a long while ago. Big 'ammer, long lever and a hacksaw and it now doesn't vibrate any more. Replaced a drag-link track-rod end, wing panel indicator, and just went round checking bolts etc .. which was good 'cos the offside spring retaining bolts were loose, I guess the plate has bent .. might sort some thicker steel for them later.

Tomorrow I'll check the wheel bearings again, all the oils and just fettle stuff .. ;)
Click to expand...

Have you fixed that wing you damaged at Pateley :D:D:D
 
suew said:
Have you fixed that wing you damaged at Pateley :D:D:D
Click to expand...

Nah, 'tis but a scratch ..

A deep, long, wavy scratch, but a scratch nonetheless .. ;)

Mind, I did have to pull the denty bit out a bit 'cos the door was catching it as it opened.
 
Just going outside to see if I can remove the dash to fix the windscreen washers. Will be back in a minute when I get stuck :eek::eek:
 
suew said:
Just going outside to see if I can remove the dash to fix the windscreen washers. Will be back in a minute when I get stuck :eek::eek:
Click to expand...

Yep I'm stuck. Its mostly in bits and I had a trip to the shop for the right screwdriver but it still wont come out.

Still it took an hour to get to this point, an definite improvement :D
 
??? just take the dash top off to get to mine...

3/4 screws in the top, 4 holding the dash top vents on, instrument binnacle (4 screws) and both end caps, drivers side is 2 screws, as is passenger, one screw hiding under the landy logo on the side. 2 or 3 more under the front edge.
 
timtheenchanteruk said:
??? just take the dash top off to get to mine...

3/4 screws in the top, 4 holding the dash top vents on, instrument binnacle (4 screws) and both end caps, drivers side is 2 screws, as is passenger, one screw hiding under the landy logo on the side. 2 or 3 more under the front edge.
Click to expand...

Yes, so is mine :D:D Managed to get it off. Trouble is found another fault :(:(

Still the leak will soon be fixed. It was the hose caught in the vent handle, it had chopped it in half :eek::eek::eek:
 
Driver her for 4 hours on the motorways, 70 all the way, slowing down as she heated up then foot down again when she was cool. Then she sat for a couple of days, then drive back! Lorry had a blow out next me, my inards almost fell out and thought I was a goner haha :/
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
549
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
650
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
931
Knappster
Knappster
Mooky
Replacing thermostat
Replies
14
Views
604
Mooky
Mooky
I
Re-coding of ABS Module after repacement
Replies
10
Views
1K
invisible999
I