Naf623

Naf623

Active Member
Plan to fit new mud shields this week, and I'm assuming the bolts will be shot (assuming I can even get them out). What will I need by way of replacements?

While at it, I'll be needing to remove the callipers and discs to get at them, right? Anything there I should be replacing once it's been removed, and can't be reused?
 
Naf623 said:
Plan to fit new mud shields this week, and I'm assuming the bolts will be shot (assuming I can even get them out). What will I need by way of replacements?

While at it, I'll be needing to remove the callipers and discs to get at them, right? Anything there I should be replacing once it's been removed, and can't be reused?
Click to expand...
You should be able to use all the bolts on the caliper set up again…..depending on their condition once removed !! You need to use a 12 point socket on them. As for the mud shields, the bolts will probably shear off removing them, and if it was mine I wouldn’t replace them.
 
I replaced mine as well, they were fubared.... Make sure you dip them in a bit of anti seize when you put them back in. Will give the next guy who takes them off an east time....
 
Naf623 said:
Plan to fit new mud shields this week, and I'm assuming the bolts will be shot (assuming I can even get them out). What will I need by way of replacements?

While at it, I'll be needing to remove the callipers and discs to get at them, right? Anything there I should be replacing once it's been removed, and can't be reused?
Click to expand...
Just get rid of them. They don't do anything useful. They do trap stones, which make a horrible noise rubbing against the disc.
 
Use a bit of heat on the mud sheild bolts as they'll no doubt have had locktite on if factory
 
Naf623 said:
I don't have a torch, would a heat gun achieve enough?
Click to expand...
No. In an ideal world an Oxy Acetylene gas torch is the tool for the job, but that’s not possible for most of us at home. I got a Rothenberger torch years ago I use and it’s good, but the flame is quite large so care is needed when using. As I’ve said previously. I don’t think these merit the work and expense to replace them. It won’t make any difference not having them.
 
Naf623 said:
Plan to fit new mud shields this week, and I'm assuming the bolts will be shot (assuming I can even get them out). What will I need by way of replacements?

While at it, I'll be needing to remove the callipers and discs to get at them, right? Anything there I should be replacing once it's been removed, and can't be reused?
Click to expand...
As said heat on them if seized (they also have thread lock on them).I used a blow torch as that's all I had & single hex socket or spanner & luckily fr. & rr's all came out. I had mine blasted & I then painted them & re fitted with stainless steel bolts, best of luck.
 

Attachments

  • 20210107_132357.jpg
    20210107_132357.jpg
    395 KB · Views: 100
  • 20210214_165200.jpg
    20210214_165200.jpg
    392.6 KB · Views: 98
  • 20210216_095942.jpg
    20210216_095942.jpg
    423.6 KB · Views: 105
  • 20210213_162510.jpg
    20210213_162510.jpg
    269.9 KB · Views: 99
  • 20210321_113302.jpg
    20210321_113302.jpg
    391.3 KB · Views: 91
  • 20210321_113253.jpg
    20210321_113253.jpg
    301 KB · Views: 100
meego said:
No. In an ideal world an Oxy Acetylene gas torch is the tool for the job, but that’s not possible for most of us at home. I got a Rothenberger torch years ago I use and it’s good, but the flame is quite large so care is needed when using. As I’ve said previously. I don’t think these merit the work and expense to replace them. It won’t make any difference not having them.
Click to expand...
+1 on Rothenberger
Irwins might also help
New besties.JPG
 
Give the bolts a smack head on with a hammer, to loosen the rust grip... Got that tip from Mike, Britannic Restorations. Works a treat.

I wouldnt be without a full set of irwins extractors. Got me outa' the sh1t many times....
 
You must log in or register to reply here.

Similar threads

L
SEPERATING BRAKE CALIPERS - WHY IS THIS A NO NO??
Replies
2
Views
483
Pawl
Pawl
frostythor
My Last MOT
Replies
1
Views
531
lynall
L
L
GETTING SWIVEL TO AXLE BOLTS OUT!! - they are out!!!
2
Replies
29
Views
2K
Forrest Gump
F
Rusty Bucket
Modify front brake hose bracket
Replies
3
Views
410
v8250
v8250
L
Hand brake question
Replies
14
Views
1K
romanrob
R