Bobsticle said:

Weldy.

Do us a piece on turning a stick welder to max and spraying slag all over the joint until you get a thick enough crust to hold about six tons. I have a big job breaking out next week.

Click to expand...

Bobsticle said:

Weldy.

Do us a piece on turning a stick welder to max and spraying slag all over the joint until you get a thick enough crust to hold about six tons. I have a big job breaking out next week.

Click to expand...

Weldy said:

haha
Its actually surprising how strong a poor weld is!!
Do you want me to do a stick welding" how to"
Basic instructions will change your lives!

Click to expand...

Bobsticle said:

Go for it Wendy................

Click to expand...

1. I'm only Wendy on a Friday !!
2. Welding in short skirts is not recommended
3. But if you want Wendy to show you how to
4. Friday it is with the short skirt

dieseldog69 said:

@Weldy It's now Sunday.

Where's Wendy in her short skirt stick welding?

Click to expand...

Weldy said:

Wendy will be doing her show tomorrow mate! She was off her rocker on Friday!! So she's all preped to go tomorrow! She's on the same meds as me so I couldn't hold the camera and she couldn't weld as we were both in cloud cookoooo!
Divnt worry , Wendy will have her short skirt and high heels on tomorrow night for you!
Cracking legs she's got!!

Click to expand...

Weldy said:

Sexy!!! But Nowt compared to wor Wendy!
She's a bit camera shy so she will have her helmet on but she loves a rod in her hand and she knows what to do with it too!! We are going up to work tomorrow afternoon, so will have it all edited by tomorrow night!

Click to expand...

kurtjohnson10 said:

i may have to eat lunch after then pmsl

Click to expand...

Weldy said:

Haha!! She up for going on top totty thread aswell But just in he knickers and bra!! Nee minge or nowt showing!!
Face hidden! Just like readers wives sometimes !!!

Click to expand...

kurtjohnson10 said:

or tinder

Click to expand...

Weldy said:

Haha!! She up for going on top totty thread aswell But just in he knickers and bra!! Nee minge or nowt showing!!
Face hidden! Just like readers wives sometimes !!!

Click to expand...

Weldy said:

Howdy doo!
Just a few photos and tips on Velding that has been done today!
Back cross member thingy at back below door on D1View attachment 145829 I premake my repair pannel first and draw around it with chalk. Always go at least 2 inches past your last bit of rust! As it may look solid but it won't be
View attachment 145831using thin cutting discs , cut on the lines you have drawn ! Its is easier to sand some metal off later than to fill big feckin gaps!
Once cut out paint the inside of the cross member with paint (obviously)
View attachment 145832 I tack little bits of metal on the edges of my repair pannel as it helps for it to sit flush ! Some people use magnets to hold the pannel in place but I have found you get loads of crappy bits of metal stuck to it and you end up with hairy magnets View attachment 145833 you would ideally put a tack every 30mm. this prevents the pannel distorting when welding ! Also stagger your welds , do a bit at the left , then the opposite side then the middle then the left blah blah blah! You get the idea! It stops heat build up and prevents it warping!!
Ideally you should have a gap of 1 mm to aid with penetration, as we all love penetration! But when using 1.2 mm thick steel its difficult and you start blowing holes through if your an intermediate skilled welder. If you do blow holes, just join lots of little tacks together until it fills the gap!! It ain't an oil rig we are welding so it don't have to be Perfik. Little pick of my welding View attachment 145835once welded, grind the feker down flush!! The aim of grinding is to only take the weld off and not grind into the patch or vehicle! We've all done it and ended up with geet big gouges !! Anyhoo after grinding then sanding , cover it with thick paint so nobody can see how rough your metalwork is View attachment 145836 hope this helps people's
Weldy

Click to expand...

Weldy said:

Hi people's! If you don't mind me and Wendy can't provide the video at the moment, as we have just had some brilliant news and are going to celebrate !
So me and Andrea are celebrating and I can't leave Wendy on her own in supervised ! Health and safety shyte!! Will have to be tomorrow! I do apologize!
Its as if we have won the lottery!!
Our lives have changed in minutes for the better !!
Sorry to dissapoint! But it's the first time in our lives we've had the winning cards !!
Defo put the show on this week though!
Just its party time !!
King regards
Paul and Andrea
Aka
Weldy and Mrs weldy!

Click to expand...

Shimsteriom said:

Intrigued now... will you let us know what you're celebrating in time?

Click to expand...