R

rjw2012

New Member
Hi.
I took my discovery 300 tdi off-roading for the first time Sunday, and had a great day. I have got 235 70 r16 BFG mud terrain tyres on steel rims, and found the rear wings have cut in to the tyres. Somebody suggested replacing the springs (with new standard ones), but wasn’t sure if this is going to help? Any suggestions would be great.
Thanks Ryan.
 
it is catching much higher up inside the wheel arch? is there an easy way of stoppin the wheel goin up that high? i thinks it might b because the steels stick out further than the alloys did.
 
get the arch extentions on fleabay around 130 there fitted abit higher so you can cut you arches higher giving you better wheel travel just remeber to repaint the arches lol
 
modulars and 8spokes have quite an offset and will cause your tyres to catch with the wide tyres, disco steels won't (the old 5spokes you can get for £10 each or less from a breaker)
 
G-man said:
modulars and 8spokes have quite an offset and will cause your tyres to catch with the wide tyres, disco steels won't (the old 5spokes you can get for £10 each or less from a breaker)
Click to expand...

Ok thanks. They are 8 spoke. Just tryed to upload a pic but it wont work.
 
same prob I had years ago when I fitted 235/70/16 muds to a Rangie on standard springs. Tyres were not rubbing onto the wheel arch lips, but were rubbing onto the top arch, where seat belts are anchored. Only happens on full articulation tho.

You can fix this by either

1) fit extended bump stop (will decrease articulation a little tho)

2) fit 1" suspension block under the spring seat & extended bump stop (so that springs are not compressed fully on full articulation)

3) fit +1" or +2" rear springs & extended bump stop

In case you do not know where the bump stop is, looked at your rear axle at approximately 6" inwards after the spring. You'll see a flat section on the axle, the bump stop is right above.
 
I ran 15x7 8 spokes for a while with 31x10.5 recip trial and only got a bit of panel bending/tyre cutting just below the rubbing strip at the back of the rear arch.

This was with a camel cut, 40mm lift block and stock bumpstops.

I'm suprised you are getting bad tub rub, usually it's the panels that get it first, usually the tubs are out of the way with small Tyres.

Defo check bump stops :)
 
Something is wrong - this size of tyre on a std Disco I should not be rubbing.

I would checking/replacing your rear springs.
 
Even with no springs it shouldnt rub, providing the bump stops are right.

I assume it has stock length dampers...?
 
Thanks for all the replies. I have checked the bump stops and they look fine. Im sure its because the steels they are on are off set, the spare is sitting a good 2 or 3" away from the the rear door where the old spare sat alot closer. Think i will have to change the steels.
 
Last edited:
The wider wheels are better, but obviously there is a trade off!

If you don't want to cut the arches then they're probably never gonna work!!
 
You must log in or register to reply here.

Similar threads

A
2015 Defender 90 - best road tyres
Replies
11
Views
3K
sidfish
S
H
Yes folks! It's tyre pressures again....
Replies
7
Views
2K
Hector the Bad
H
K
What money should I be asking?
2
Replies
27
Views
4K
Karls
K
02Disco2
Disco 2 Buying 16” rims - what can I get away with
Replies
8
Views
1K
02Disco2
02Disco2
BigRedDisco2
New wheels advice needed
Replies
2
Views
729
BigRedDisco2
BigRedDisco2