madbrit

madbrit

Active Member
Hi all, just bought a TD6 2003 Auto

It has No Suspension Control Panel Lights and no controls work on that panel also compressor is not working so no suspension ;(

No warning On Dash Saying Inactive ???

Any one point me in any direction

As my nanocom will not work and never will on this car I have been told by black box, so I have a snapon unit on its way, but want to have a dig round

Any help greatly received

MadBriT
 
madbrit said:
Hi all, just bought a TD6 2003 Auto

It has No Suspension Control Panel Lights and no controls work on that panel also compressor is not working so no suspension ;(

No warning On Dash Saying Inactive ???

Any one point me in any direction

As my nanocom will not work and never will on this car I have been told by black box, so I have a snapon unit on its way, but want to have a dig round

Any help greatly received

MadBriT
Click to expand...

When you say "no controls work on that panel" what about the clock, boot release and parking sensors?
 
yep they all work, just no response from the air suspension controls, By no lights i mean no height status lights
 
Looks like you need to wait for your snapon so you can read/clear the errors before anything will happen.
 
  • Like
Reactions: kds
EAS is in a "hard fault" condition hence the lack of height selector lights and the dead compressor.
 
What is meant by HARD FAULT and what about the battery ? What do I check for ? Charging rate. Volts amps ?
 
There some checks in the system that can be deemed as fluke or passing and the ecu can sometimes keep checking and if not present the next time won't highlight the issue but then after a certain amount of times a more severe issue the system will shut down to protect components or possible further damage to the car.
 
A hard fault or shut down situation has to be diagnosed, repaired and cleared for the system to come back Into play;)
 
A good battery is 12.6v and above 12.4v and lower is gone, check volts engine off then check with engine running at 2000rpm and everything turned on and you should have about 14.7v which is a good alternator output.
 
Mark Piercy said:
A hard fault or shut down situation has to be diagnosed, repaired and cleared for the system to come back Into play;)
Click to expand...

Henry_b said:
EAS is in a "hard fault" condition hence the lack of height selector lights and the dead compressor.
Click to expand...
Recently had same symptoms. I even got told it was a height sensor fault. It resolved itself when the rear tailgate lock was replaced and battery was charged fully.
 
gold rover said:
Recently had same symptoms. I even got told it was a height sensor fault. It resolved itself when the rear tailgate lock was replaced and battery was charged fully.
Click to expand...
So the ecu could have been isolating the system and thinking the rear tailgate was open? Did you have any Interior lights on as well?
 
Well i never. Plug the diagnostics in. First make sure all is working. Pump ok. Tank holding 8bar. All valves working. Headlight adjuster ok. So I think let’s do a calibration. Directly that was done. Turn ignition off re start car and it all comes to life. Well I never. But there was no fault on the dash or the diagnostic screen weird or what :) happy now as bought cheap as suspension not working and was smoking. Smoking was a blocked filter at the back of engine suspension needed calibrating. :) Tanks to all
 
Good news that it's all working but I'd re check the tank pressure after it's been running for a few minutes. See below from manual

The compressor is used to supply air pressure to the air suspension reservoir. The ECU monitors the pressure within
the reservoir and, when the engine is running, maintains a pressure of:
13.7 bar (199 lbf/in2), in systems without an external pressure relief valve
11.8 bar (171 lbf/in2), in systems with an external pressure relief valve
 
I'd keep an eye on the compressor temperature as well. I usually get 2 or 3 goes at callibrating before it overheats and shuts down until it cools enough to restart.
It may stop filling the tank until it cools enough to continue.
 
funny, my son helped with the calibration and he said lets do it a few times to make sure, so will leave it a few min between,

Thanks
 
Is this what you mean

upload_2021-9-14_13-58-24.png
 
You must log in or register to reply here.

Similar threads

B
rangerover l322 2006 td6 air suspension
Replies
5
Views
849
backinblack
backinblack
O
03 L322 EAS ECU Can bus fault / ABS temp system deactivation
Replies
1
Views
628
oldradiotech
O
G
L322 No communication with air suspension with diagnostics
Replies
3
Views
2K
Mark Piercy
Mark Piercy
T
L322 no illumination on instrument cluster
Replies
14
Views
2K
gstuart
gstuart
rover75lover
L322 l 322 air suspension
Replies
12
Views
2K
backinblack
backinblack