B

bombx3

New Member

• May 19, 2010

• #1

I have lost a bit of low end power
I have read loads on this site about the maf and am totaly confused
Mine is 6mts old and gives no nanocom faults it says on 740rpm 40gm
so i disconected the plug and it pulls smoother and a bit more power, is my maf broke again!

 

Essex Mike

Member

• May 19, 2010

• #2

I its 6 months old, then take it back to the dealer, get them to fix it under the warranty...

 

B

bombx3

New Member

• May 19, 2010

• #3

the landy isnt 6mths old the britpart maf is

 

johnlad

Well-Known Member

• May 19, 2010

• #4

bombx3 said:

the landy isnt 6mths old the britpart maf is

Click to expand...

patten part maf's are prone to failing and giving false info to the ecu combine that with Britpart and your asking for trouble, buy a genuinne maf about £75 should solve the problem

 

B

bombx3

New Member

• May 19, 2010

• #5

thanks for that .Britpart should be hanged and tortured for selling substandard goods
£75 for another maf is quite a shock !

 

Shifty1962

Well-Known Member

• May 19, 2010

• #6

bombx3 said:

the landy isnt 6mths old the britpart maf is

Click to expand...

If it's lasted 6 months it's done well

 

P

Pommy Pekkie

Member

• May 19, 2010

• #7

Shifty1962 said:

If it's lasted 6 months it's done well

Click to expand...

Should be reading about 60 if I remember correctly. Mine was also reading around 40 and felt flat. An OE one got it sorted.

Tom

 

B

bombx3

New Member

• May 20, 2010

• #8

the result is it now revs it tiny little big ends off ! brill 760 rpm 60gr
But still lost its power untill turbo kicks in ,any one know why ?

 

B

bombx3

New Member

• May 20, 2010

• #9

£92.70 from mattford landrover,but it now revs out
But its rubbish untill turbo comes in there is something else wrong ,nothing is showing on the nanocom
any ideas?

 

johnlad

Well-Known Member

• May 20, 2010

• #10

have you cleaned your map sensor on the inlet manifold

 

B

bombx3

New Member

• May 20, 2010

• #11

i did that one the other day i found out it was a problem on some on elses thread.if the sensor was at fault would it show on the nanocom

 

J

jsbholden

New Member

• May 20, 2010

• #12

Poss not. it could be giving a lower reading. would only reg on nanocom as a fault code if the sensor packed up and caused the ECU to use a default value

 

B

bombx3

New Member

• May 20, 2010

• #13

do they break down much
can i test one?

 

J

jsbholden

New Member

• May 21, 2010

• #14

You need to colect live data from nanocom, ideally under load. Find a long hill and drive up it with revs about 2500-3000rpm. Should be getting a Reading of about 220 from the map sensor

 

B

bombx3

New Member

• May 21, 2010

• #15

do you no what it is called on the nanocom i cant see map sensor

 

J

jsbholden

New Member

• May 21, 2010

• #16

From memory I think it's turbo presure. Figure is in kpa

 

B

bombx3

New Member

• May 21, 2010

• #17

ar 3450 206kpa
at 3000rpm it reads 196 kp
at 2062 120 kpa

 

B

bombx3

New Member

• May 21, 2010

• #18

780 rpm is 104 kpa

 

B

bombx3

New Member

• May 21, 2010

• #19

what i have seen is oil in the injector plug in bits but it hasnt tracked ,the britpart loom is only 10mts old
No nanocom fault shown

 

B

bombx3

New Member

• May 22, 2010

• #20

fitted new loom no good
thinking about breaking my relationship with landrover because its driving me mad!