RobRainford

New Member
I've been wiring in my sub today I've got a 6 pin moles plug that plugs into the subs amp. Out of which there's a brown earth lead, a red power lead and a blue lead. I found out that this is a remote lead and it can either be wired to a 12v feed or a switch. I will be wiring this to the battery so the sub comes on with the ignition. My issue lies when I connect the red and blue wires to the battery, the sub will come on even though the earth lead isn't connected at all! It's puzzling me why this is happening!

The cable routing issue, is where can I get the RCA connectors to inside the dash behind the stereo? It seems a sealed unit. Is there any easy way to get these cables in bar drilling a hole somewhere?
 
earthed through the mounting screws???

I'd put the blue wire to a switch personally when wading I like to turn it off I have popped 2 amps to date plus you don't want it on all the time it can be serious drain on the battery
 
earthed through the mounting screws???

I'd put the blue wire to a switch personally when wading I like to turn it off I have popped 2 amps to date plus you don't want it on all the time it can be serious drain on the battery

It's mounted through Mdf and the only connection is currently the live to the battery. I can't figure out where it's earthing to.

I am contemplating a switch or wire to auxiliary on ignition if there is one? T
 
I've been wiring in my sub today I've got a 6 pin moles plug that plugs into the subs amp. Out of which there's a brown earth lead, a red power lead and a blue lead. I found out that this is a remote lead and it can either be wired to a 12v feed or a switch. I will be wiring this to the battery so the sub comes on with the ignition. My issue lies when I connect the red and blue wires to the battery, the sub will come on even though the earth lead isn't connected at all! It's puzzling me why this is happening!

The cable routing issue, is where can I get the RCA connectors to inside the dash behind the stereo? It seems a sealed unit. Is there any easy way to get these cables in bar drilling a hole somewhere?
you are going about this the wrong way the little blue wire is your remote lead which goes to the blue remote lead that comes out of the back of your head unit which tells the unit to power up and yes it can be in a mdf box the subb will still power up of sorts and why do you have the power cable connected direct to the sub ?? how it should be is red cable goes to pwr on amp brown earth goes to gnd on amp and blue remote goes to rmt or rca then you need a length of HIGH QUALITY speaker cable coming out of the amp but is your amp a 1 channel 2 channel etc look at the terminals you should find a + and a - and they will be in pairs for each channel and as for the routing the cable time to pop your door rubbers off and take that trim piece off between the door and carpet the run your cables in that space and for running it in to the back of the head unit you run it up the door pillar and out of view and in to the back of the dash you will find a gromit to where you poke the wire through with ease (very easy on drivers side) then have a 2m length of small quage wire and the glovebox open and a screwdriver and go fishing you will find the wire very easy and then join it up and pull it through jobs a gooden then solder the remote to remote and your good
 
you are going about this the wrong way the little blue wire is your remote lead which goes to the blue remote lead that comes out of the back of your head unit which tells the unit to power up and yes it can be in a mdf box the subb will still power up of sorts and why do you have the power cable connected direct to the sub ?? how it should be is red cable goes to pwr on amp brown earth goes to gnd on amp and blue remote goes to rmt or rca then you need a length of HIGH QUALITY speaker cable coming out of the amp but is your amp a 1 channel 2 channel etc look at the terminals you should find a + and a - and they will be in pairs for each channel and as for the routing the cable time to pop your door rubbers off and take that trim piece off between the door and carpet the run your cables in that space and for running it in to the back of the head unit you run it up the door pillar and out of view and in to the back of the dash you will find a gromit to where you poke the wire through with ease (very easy on drivers side) then have a 2m length of small quage wire and the glovebox open and a screwdriver and go fishing you will find the wire very easy and then join it up and pull it through jobs a gooden then solder the remote to remote and your good

Like what he said.

But with more punctuation and paragraphs. :D
 
I interrupted the remote blue wire with a switch as I didn't
Fancy the amp being submerged and then the stereo fires up and boom amp gone.

I can deal with getting it wet as long as there is no power on the pcb except the relay.
 

Similar threads