C

Colonial

Well-Known Member
After realising that I'd got an occasional flat spot when taking my foot of the accelerator, I've decided to fit a new set of silicone turbo hoses. The existing rubber hoses are soft when pressed. My current layout is thus (see below pics) They've been ordered off e bay for £30.00 (free delivery) this week!

I would welcome any views or advice before I roll up my sleeves?

Before anyone say's "Buy cheap, buy twice". Look at this.
http://www.msn.com/en-gb/foodanddri...e-price/ar-BByQXrx?li=AAmiR2Z&ocid=spartandhp

:)
 

Attachments

  • IMG_6403 (2).JPG
    IMG_6403 (2).JPG
    284.2 KB · Views: 277
  • IMG_6404 (2).JPG
    IMG_6404 (2).JPG
    269 KB · Views: 229
  • IMG_6405 (2).JPG
    IMG_6405 (2).JPG
    236.3 KB · Views: 288
Last edited:
Made quite a difference to mine. Smoother power delivery being the most notable.
Mine are British manufactured though, £60 for a set of pre facelift.
Can't really see a problem with the cheaper ones, although some have had to trim them a bit to make them fit.
Mike
 
the only thing with these silicone turbo hoses is the 90 degree one is not quite right I measured the end of the egr and the other end where it goes and the egr end is slightly smaller I have been in touch with DPH in derby and the man there said ring the people in the workshop and they will make you one to fit , But why are they not doing them to fit properly anyway.
 
Skinny Mike said:
Made quite a difference to mine. Smoother power delivery being the most notable.
Mine are British manufactured though, £60 for a set of pre facelift.
Can't really see a problem with the cheaper ones, although some have had to trim them a bit to make them fit.
Mike
Click to expand...
Thanks Mike. I'll bare that in mind when they arrive.
 
Jake ingleby said:
Can I ask is it worth swapping pipes for silicone ones or wait till old ones have had it then change them
Click to expand...
Mine have just about had it already. If you squeeze them they're really soft. Keep in mind Skinny Mikes observation (above) about having to trim some new one's to fit. I'll be using my old ones as a template.
 
Does anyone have a link for some hoses that you don't have to trim as I'm bound to cut them short. Mine is an 06 plate. Cheers.
 
dwalsh1 said:
Does anyone have a link for some hoses that you don't have to trim as I'm bound to cut them short. Mine is an 06 plate. Cheers.
Click to expand...
LOL you sound like me... I buy 2 of everything... one for the "oops I buggered it" and one for the "second attempt learn from your mistakes"
 
dwalsh1 said:
Does anyone have a link for some hoses that you don't have to trim as I'm bound to cut them short. Mine is an 06 plate. Cheers.
Click to expand...
dwalsh.
I used a fine bladed wood-saw to cut mine to length, then a pair of decent scissors to trim the edges. That is not the best way, I'm sure. However, the 'measure three times and cut once' rule does come into play. Also I had to release a couple of bolts holding the large plastic thingy along the top of the block to allow for a bit of wriggle room when fitting the 90 degree hose. Tomorrow, weather permitting, I'm removing the tray from beneath the motor to recover one of those bolts!
 
dwalsh1 said:
http://www.ebay.co.uk/itm/like/291183147428?chn=ps&adgroupid=38904455432&rlsatarget=pla-278028041734&abcId=923906&adtype=pla&merchantid=7284654&poi=&googleloc=9045999&device=m&campaignid=738208994&crdt=0&ul_ref=http%3A%2F%2Frover.ebay.com%2Frover%2F1%2F710-134428-41853-0%2F2%3Fmpre%3Dhttp%253A%252F%252Fwww.ebay.co.uk%252Fitm%252Flike%252F291183147428%253Fchn%253Dps%26itemid%3D291183147428%26targetid%3D278028041734%26device%3Dm%26adtype%3Dpla%26googleloc%3D9045999%26poi%3D%26campaignid%3D738208994%26adgroupid%3D38904455432%26rlsatarget%3Dpla-278028041734%26abcId%3D923906%26merchantid%3D7284654%26gclid%3DCjwKEAjw_PfGBRDW_sutqMbQsmMSJAAMpUapSksXHabNZNyqfHc3NFo1bQwWRqhmTsJn5K_Jpz_ePBoCg-Lw_wcB%26srcrot%3D710-134428-41853-0%26rvr_id%3D1192906276495
These look reasonable
Click to expand...
That's cheap for DPH hoses. Good quality those.
Mike
 
Colonial said:
dwalsh.
I used a fine bladed wood-saw to cut mine to length, then a pair of decent scissors to trim the edges. That is not the best way, I'm sure. However, the 'measure three times and cut once' rule does come into play. Also I had to release a couple of bolts holding the large plastic thingy along the top of the block to allow for a bit of wriggle room when fitting the 90 degree hose. Tomorrow, weather permitting, I'm removing the tray from beneath the motor to recover one of those bolts!
Click to expand...
Good luck :)

Skinny Mike said:
That's cheap for DPH hoses. Good quality those.
Mike
Click to expand...
That's what I thought cause I swear I see them for around £135 on another site
 
Colonial said:
Mine have just about had it already. If you squeeze them they're really soft. Keep in mind Skinny Mikes observation (above) about having to trim some new one's to fit. I'll be using my old ones as a template.
Click to expand...

It's about how much they expand under pressure not about how easy they are to squeeze. Lot of bollocks talked about turbo hoses. If the standard hoses are fine silicone hoses will make no difference to anything other than in the mind of the driver.
 
You must log in or register to reply here.

Similar threads

R
TD4 Silicone Turbo Hoses
Replies
7
Views
4K
109party
109party