greenlanebasher · Apr 11, 2010

I was just removing my rear axle breather to give it a clean out but as i turned the head of the nut the top of the breather sheered off

. I am going to try and get the breather thread out of the axle with a pair of mole grips but when i have done that where is the best place to buy new breathers from?

Thanks

smudge67999 · Apr 11, 2010

john craddocks in cannock just type it in ur browser and it will come up they got an on line dirctory

MrJC · Apr 11, 2010

LAND ROVER axle breather kit RANGE ROVER,90,DEFENDER on eBay (end time 07-May-10 17:51:59 BST)

greenlanebasher · Apr 11, 2010

smudge67999 said:
john craddocks in cannock just type it in ur browser and it will come up they got an on line dirctory

Thanks. I have had a look but what will it be called. I need the actual part that threads into the axle. Thanks again

B3aker · Apr 11, 2010

Where abouts are you buddie, i have a spare 90degree one that should fit in the back of my landy.

greenlanebasher · Apr 11, 2010

MrJC said:
LAND ROVER axle breather kit RANGE ROVER,90,DEFENDER on eBay (end time 07-May-10 17:51:59 BST)

I dont think mine are a push fit. they have a 14mm hexagon head on them so i assume they are a screw thread???

greenlanebasher · Apr 11, 2010

B3aker said:
Where abouts are you buddie, i have a spare 90degree one that should fit in the back of my landy.

I will PM you

B3aker · Apr 11, 2010

greenlanebasher said:
I will PM you

PM replied to.

Edit. I'll better go see if i still got it.

B3aker · Apr 11, 2010

I have still got it.

MrJC · Apr 11, 2010

No need to unscrew next time.... as you will see the breather pipe is the push fit into the fitting. Should have been similar on your busted one? It wasn't a plain wading plug (no tube)that was screwed in was it?

ninety till i die · Apr 11, 2010

It's called a banjo bolt (no idea why) it sounds the same as on my 90 and should look like this.

greenlanebasher · Apr 11, 2010

ninety till i die said:
It's called a banjo bolt (no idea why) it sounds the same as on my 90 and should look like this.

Yep - that looks like it but the head has sheered off in the collar that the pipe attaches to. Not enogh to grab with mole grips and it is well rusted in. I think i need to find another alternative

The Mad Hat Man · Apr 11, 2010

screw extractor?

Pikey · Apr 11, 2010

greenlanebasher said:
Yep - that looks like it but the head has sheered off in the collar that the pipe attaches to. Not enogh to grab with mole grips and it is well rusted in. I think i need to find another alternative

The collar will just lift off if the head has snapped off. and you'll have a stub sticking up. If not then eezy outs will do it.

The Mad Hat Man · Apr 11, 2010

dint I just say that?

Paul D · Apr 11, 2010

Maybe you need to shout?

Pikey · Apr 11, 2010

Did someone say summat??

The Mad Hat Man · Apr 11, 2010

I think its my cloak of invisibility

Paul D · Apr 11, 2010

Nah, I can't see that ...

greenlanebasher · Apr 11, 2010

I have heard of these thread extractors but have been told that they usually break before they shift the thread leaving me with a bigger problem than when i started. Do you rekon they would work then?

Active Member

Active Member

Well-Known Member

Active Member

Well-Known Member

Active Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Active Member

Well-Known Member

Dummy Ejection Facilitator..

Well-Known Member

Old, nackered 'n broke, but the Landy is fine . :)

Dummy Ejection Facilitator..

Well-Known Member

Old, nackered 'n broke, but the Landy is fine . :)

Active Member

Similar threads