Wildefalcon
Well-Known Member
Presume you didn't torque the bolts until you lowered it? Or are you on Poly bushes?
steve2286w
Well-Known Member
the shackle bolts should be tightened with load on them according to workshop manual
herby1
Active Member
Thanks for the suggestions, will undo & retighten U & shackle bolts today & let you know what happens.
As a relative newbie to Landy's it's a steep learning curve ( Haynes / workshop manual, YouTube, & advice on here Helps )
Does everyone Torque the U & shackle bolts or just tighten ?
As a relative newbie to Landy's it's a steep learning curve ( Haynes / workshop manual, YouTube, & advice on here Helps )
Does everyone Torque the U & shackle bolts or just tighten ?
Turboman
Mab An Gov
Just give them a good pull with a big spanner, or a socket with a 2 foot bar on it.
You need to get a genuine manual, reprints are available. All this stuff is covered. Putting the springs in the right places, lowering the vehicle before tightening the bolts, how to rebuild components.
When I was a new Series owner back in the 80s, I had a genuine manual, and I used to sit reading it every evening, until I had read it cover to cover several times. Then I went back and read sections of special interest again.
And that was even though I had been working on cars, motorbikes, and boats, for five years already.
Turboman
Mab An Gov
Greasing the leaves with graphite grease is also a good idea. Improves the ride with new or old springs.
steve2286w
Well-Known Member
The shackle torque is 60-70lbs ft and u bolts 58lbs ft so not that high, when I put my new axle on I just nipped them up and a month ago thought I would torque them in case they loosened. If you’re a bit heavy handed use a torque wrench or it is esp important (inside engine etc) but generally you may a develop a feel for what torque feels appropriate for size bolt working on.
herby1
Active Member
undone & retightened U & ( shackle bolts with load on ), didn't make any difference, loosened all, jacked chassis up on lower side, & retightened so gap was both 2.5in, when lowered, returned to about 1 inch gap.
OH, & rung off the thread on the squared U bolt ( a lot of swearing ), had bottle jack under plate but popped the thread, so ordered a few spare U bolts from paddocks.
OH, & rung off the thread on the squared U bolt ( a lot of swearing ), had bottle jack under plate but popped the thread, so ordered a few spare U bolts from paddocks.
Last edited:
herby1
Active Member
Forgot to say, when it was all loosened, I stood half in engine bay / bumper & worked the suspension a bit ( 21 stone 
) to see if it settled ( it didn't ), can't drive it at the moment but should be road worthy soon, will try a bumpy road, see if that works.
Any other ideas appreciated
) to see if it settled ( it didn't ), can't drive it at the moment but should be road worthy soon, will try a bumpy road, see if that works.Any other ideas appreciated
Turboman
Mab An Gov
Sit in the passenger seat, and get someone lighter to drive. It should be level.Forgot to say, when it was all loosened, I stood half in engine bay / bumper & worked the suspension a bit ( 21 stone
Any other ideas appreciated
steve2286w
Well-Known Member
good to have spares just in case
have you followed the spring setting procedure and getting measurements as in point 12 below, the manual also has the camber measurements for each spring which you can compare with also but best done when off the shackles
codfather79
Well-Known Member
Out of interest, what difference does it make if you have poly bushes?
I've used poly bushes, fitted when the chassis was swapped, but with the assistance of a LR mechanic, so I may have missed why or how he went about it.
Turboman
Mab An Gov
Shouldn't make any difference at all.
Some people think if you have polys you can tighten the bolts before lowering the vehicle. I don't, so I don't.
