Well,

Replaced head gasket tightened down as to Haynes.

Started up and .....

Still white smoke , me thinks head is F##cked
 
New head complete coming today from Land rover with new gasket new head bolts have invested in new angle torque wrench .

Hopefully this will cure ,

Does anyone know if the complete head is straight bolt on or does it have to be set up before fitting ?
 
Attached pictures of where I am , new head ready to go on after swapping over injectors , plugs thermostat housing .
Fingers crossed for dry day tomorrow.
 

Attachments

  • image.jpg
    image.jpg
    341.1 KB · Views: 253
So new head on after a bit of smoke / mist for first 30mins all cleared and can now drive down the road without laying a smoke screen.

Now I have 2 issues left .
1 temperature needle not moving
2 still no heating in the cab

Hope it's dry tommorow...
 
Hi advice needed.

Temperature gauge now resolved .

But I only have heat at over 2500 revs and now the smoke has returned NOT on tick over but intimitantly when driving along . Any ideas ?
 
Hey any thoughts on this ?

At the moment very ****ed off . sitting with 5lts of petrol and a pack of matches in hand !!!!!
 
Drives fine no loss of power but still smoking when driving but not on idle vehicle does not overheat HELP
 
Ok ,

No longer smoking ??? Did find one losse head bolt which was weeping oil put half a turn on this so now 120nm .

Strange as I followed the Haynes bible .

Now just no heat ..........
 
Ok ,

When down to motex to get water pump and heating is now blowing nice and hot and no more smoking ??
 
hi all ,

Welding work will be carried out on disco next week and have been buying a few bits so I can do all in one go .

Bit I'm having trouble finding are what appear to be body mounts on chassis at front inline with engine.

I will get a picture up tonight when I get home but have searched and everyone I look at is completely different.
 
pictures of the rust.

She will be saved !
 

Attachments

  • IMG_1009.JPG
    IMG_1009.JPG
    37.5 KB · Views: 194
  • IMG_1008.JPG
    IMG_1008.JPG
    107.3 KB · Views: 204
  • IMG_1007.JPG
    IMG_1007.JPG
    50 KB · Views: 218
  • IMG_1006.JPG
    IMG_1006.JPG
    44.8 KB · Views: 211
  • IMG_1005.JPG
    IMG_1005.JPG
    56.2 KB · Views: 211
More pictures of disco after welding and painting.

One side left to do.
 

Attachments

  • IMG_1031.JPG
    IMG_1031.JPG
    57.1 KB · Views: 195
  • IMG_1030.JPG
    IMG_1030.JPG
    61.5 KB · Views: 214
  • IMG_1022.JPG
    IMG_1022.JPG
    47.1 KB · Views: 232
  • IMG_1021.JPG
    IMG_1021.JPG
    49.3 KB · Views: 226
  • IMG_1027.JPG
    IMG_1027.JPG
    54.3 KB · Views: 200
  • IMG_1026.JPG
    IMG_1026.JPG
    57.7 KB · Views: 190
  • IMG_1028.JPG
    IMG_1028.JPG
    48.3 KB · Views: 229
  • IMG_1020.JPG
    IMG_1020.JPG
    56.2 KB · Views: 217
  • IMG_1032.JPG
    IMG_1032.JPG
    52.6 KB · Views: 189
Thanks ,

Have managed to get some Hempel paint to go over the chasis next weekend.

Same stuff they use on oil rigs to stop them rusting so hoping it will standup well on the Disco
 
Ooh, another rotten old Disco being saved :D

Missed this the first time round, seems it did over heat just they didn't know about it :rolleyes:

What are the bigger future plans Russ?
 
Not sure yet ,

Got it cheap as the HG went and misses is pregnant and 110 wont get in the car park due to 2inch lift .

Thinking now its all welded up finish treating the chassis then wheel arch kit bigger tyres new rear bumper as its starting to go.
 

Similar threads