StuRox

Well-Known Member
Have also posted this in the wanted section, but also here, given my idea might be of use to someone else...

Just wondering if anyone has any old Roof Rails lying around off a D1 that they don't want, as looking at an idea of making a separate set of rails to extend the ones I have to make a full length version, so ideally I need two sets to weld them together in a mad scientist way to bolt onto the roof!

Idea is something like this.....


normal_20160129_095231.jpg


and then I can use the bars across and remove them like the front ones.

Am based near Bath/Bristol if anyone is local I can pick up....


I have normally made the full expedition racks in the past, but reckon this will save a hell of a lot of metal and weight, and also look semi factory fit??

What you guys think?

Cheers
 
you can get the extending bars, but they were only for the D2 from what I have found out, plus they seem to go for silly money when they pop up on ebay.

much better fabricating something for yourself ;)
 
I don't use my bars that go across so you are welcome to have them, but I don't have spare rails.
 
Ok thanks for the offer.

I think i will be sorted come tomorrow and will let you know.
 
Well, the plan is now a goer, thanks to fellow member Saltlick for the parts ;)

Have now got everything I need to start on this idea.....

normal_20160130_160159.jpg


Now I just need to find the time.....
 
My 30mm hole cutter landed today for making the holes in the roof to allow the bars to sit properly.

Hoping the weather will stay dry at the weekend and if so will have a go at fabricating them up.
 
First day without rain so thought i would make a start.....which didn't go too well....

Rails are aluminum which i cannot weld.

Have got another idea up my sleave...just got to get more supplies before i can start mk2 version.
 
I do have a work around idea, just need to find the time to get to my local steel supplier and see if will work.....but thanks for the heads up on the EZweld rods ;)
 
I have now got the steel I was after in the hope I can make new rails over the aluminium ones to try and keep the standard look and still use the mountings.

Will hopefully get a chance to do a bit of cutting and welding at the weekend.
 
Have now made some progress, as crappy rain so have managed to get some time in the garage.

I started with some 3mm box steel...

normal_1~0.jpg


then made up a little sample to see if it would work, and fitted nicely over the bar...

normal_2~0.jpg


So with that working, made up a full length bar, cut out the bottom, bashed it together, welded and grinded it down...

normal_3~0.jpg


normal_5~0.jpg




normal_6.jpg


normal_4~0.jpg

and then painted...
normal_7.jpg


just need it to dry and then I can drill in the mounting holes for the crossbars and then put them on the roof :)

Once on the roof I will seal up the gaps with the sealer that I use to stop the roof leaking to make it look more of a professional look ;)
 
All done and fitted :)

normal_20160215_164454.jpg


normal_20160215_164541.jpg


normal_20160215_164556.jpg


Not too bad considering the price it cost me (cheers Saltlick :cool:).

A lot lighter than the full expedition racks that I have made and fitted in the past.

Would have preferred if I could just have welded the bars together and not needed the box section, but at least it is now more heavy duty :D
 
Looks good, excellent job, not seen that done before. It's quite low profile at the back, might be difficult to tighten roof tent bolts if someone wanted to do this for that reason. I am sure I still have my cross bars in the garage if you need more infill.
 
Cheers mate.

I wanted to try any keep it low and not increase the height to still get into car parks etc, as it was very limiting when i had the expedition rack on.

Not going to fit any more cross bars as I reckon 3 are enough as that's whats on the front bars and they are slightly longer than these ones.

Got enough room to fit roof box fitting or ratchet straps to tie down large items.
 
It's a good idea that ive been meaning to do something about my roof rack just use some of my dads old paddy hoppkerk transit van ones. But they are bit high and fiddly to fit.
 

Similar threads