L

landymangib

New Member
Hi, I've looked at the other thread regarding exhaust mods. I live in Gibraltar and a local company are willing to remove the cats and centre box for me as I've requested a straight through pipe. I only use the car off road and want the smiles per gallon effect. If I remove the Cats, will I have to get the ECU reprogrammed or will it run ok?????

Classic Kev or Teflon usually has the answer but if anyone has done this mod I would be pleased to hear from you.

Many thanks

Mark
 
had my rr classic done. de cat exhaust, removed egr valve, and had bigger intercooler. Allisport did the work to a very high standard. Hope that helps
 
If we are talking V8 petrol then the tune resistor in the ECU needs to be changed to a Saudi tune as they don't have cats in that country. By removing the mid box u may find a problem because of the lack of back pressure.
I change my cat back exhaust to a tuned Janspeed system so it now has a brilliant sound/tone and no probs due to the lower back pressure just a better throttal responce.
 
you may have to relocate the o2 sensors, im not sure about land rovers, but we do this with Audi's all the time. to need to move the O2 sensor or it will throw a Check engine light. are you going to gut the stock cats, or just put in custom straight downpipes?
 
Outer banks NC usa, i wrote up a long introduction of myself. ... waiting for the mods to review it??
 
yesmar said:
you may have to relocate the o2 sensors, im not sure about land rovers, but we do this with Audi's all the time. to need to move the O2 sensor or it will throw a Check engine light. are you going to gut the stock cats, or just put in custom straight downpipes?
Click to expand...

how would one gut the cats, i assume this means taking the cats out of the 'bubble' in the exhaust, can it be done so as to leave a standard looking system.

reason i ask is i use lpg so have no need for the cats, one has come loose and rattles, i dont fancy welding the pipes as they never last and a full replacement is a bit pricey this side of xmas

what method do/did you use or know of??
 
yesmar said:
Outer banks NC usa, i wrote up a long introduction of myself. ... waiting for the mods to review it??
Click to expand...

my favourite spot ere in kernow...

Porthleven.jpg


sharp pointy boulders lye 2 feet beneath...:eek::D
 
gavbriggs said:
how would one gut the cats, i assume this means taking the cats out of the 'bubble' in the exhaust, can it be done so as to leave a standard looking system.

reason i ask is i use lpg so have no need for the cats, one has come loose and rattles, i dont fancy welding the pipes as they never last and a full replacement is a bit pricey this side of xmas

what method do/did you use or know of??
Click to expand...
yes we do it in the audi's just for that reason to make it LOOK stock if you are getting a car inspected they look under it and see "o ok the catalytic converters are there"
this is free. just takes some time and patience

Now ive never done this on a land rover but
we take the down pipe off, and if you are good at cutting and welding people will cut the cat open and cut out the cat filter and pre cat, and weld back together. or my method you remove the downpipe and pry and grind away at the cat + and pre cats until it is empty. here is a diy wright up for an audi B5 S4

this is the cutting method
AudiWorld Tech Articles click "engine" then click "s4" it is labled "DIY Downpipes (Off Road Use Only)" very good write up

this is the way i do it. no welding tools
DIY: B5 S4 - Removing DP's to make Piggies (For 6spd) - Audizine Forums

sorry guys i just got my land rover on saturday, and im coming from an audi
 
Last edited:
Had mine fully de-catted, (the two pre-cats in the 'Y' section, and the main cat itself), whilst also having a custom stainless 'Y' piece made up and the rear silencers sleaved.

It didn't make any noticable differance to fuel econamy, it did help the engine run a little cooler, and it did make it sound a lot better without sounding hollow or tinny. It also popped and banged on the over-run a lot more, and I reckon liberated a few extra horses.


Luckily I have a youtube vid of it right here; [ame="http://www.youtube.com/watch?v=m5FKfGgN0AY"]YouTube - TVR Cerbera & Chimaera at Elvington[/ame]

Be sure to turn it up to 11 :D
 
gavbriggs said:
how would one gut the cats, i assume this means taking the cats out of the 'bubble' in the exhaust, can it be done so as to leave a standard looking system.

reason i ask is i use lpg so have no need for the cats, one has come loose and rattles, i dont fancy welding the pipes as they never last and a full replacement is a bit pricey this side of xmas

what method do/did you use or know of??
Click to expand...

I'm sure I saw an article on Rangerovers.net on how to empty the cats.

Current thinking is that this has been done to mine. Unfortunately it sounds a bit horrible. I assumed it had a cracked manifold, but it went to the garage yesterday and their conclusion was that the cats had been emptied - nothing wrong with the manifolds. It makes a echoing clattery noise which I find really irritating but not quite enough to make me buy new cats yet.

Since it's just passed an MOT I assume that emmisions aren't a problem (lpg).

Guy
 
Disco Moneypit said:
Had mine fully de-catted, (the two pre-cats in the 'Y' section, and the main cat itself), whilst also having a custom stainless 'Y' piece made up and the rear silencers sleaved.

It didn't make any noticable differance to fuel econamy, it did help the engine run a little cooler, and it did make it sound a lot better without sounding hollow or tinny. It also popped and banged on the over-run a lot more, and I reckon liberated a few extra horses.


Luckily I have a youtube vid of it right here; YouTube - TVR Cerbera & Chimaera at Elvington

Be sure to turn it up to 11 :D
Click to expand...

that will be back pressure loss causing fluctuating lambda sensor readings:doh:
 
You must log in or register to reply here.

Similar threads

Montyjohn
P38A A couple of queries about rebuild EAS valve block
Replies
9
Views
535
Grrrrrr
Grrrrrr
Badger688
Disco 2 Starter Motor Removal
Replies
12
Views
2K
Stanleysteamer
Stanleysteamer
Rhode rover
Removal of oil bath air filter cartridge
2
Replies
26
Views
3K
Guidoma
G
N
Looking for a 4.0l V8
2
Replies
36
Views
4K
v8250
v8250
hk_cat
P38A Rear Drivers Door Removal
Replies
7
Views
1K
modelman
M