Bordeauxdog
New Member
How did you find a clock that reads zero miles ? And where did you get the rev counter? looks fab
Last edited:
Looking at the wheel carrier can I remove the small bung in the end of the tube (you get hold of), anyone have a similar one they can look at (vehicle is not with me at the moment) as I want to get some cavity wax in it if possible, I'm going to do the same on the side steps
Last edited:
My experiences with suppliers throughout the refurbishment process (not sponsored etc etc by any of them)
Not ranked and not an exhaustive list by any means but I can expand if the demand arises
Brit Car
Great customer service both for enquiries and any issues (minor) with items supplied, good source of genuine parts (all be it at a greater cost than the alternatives)
SP-4x4
Good quality items (Galv. doors) let down by poor packing resulting in minor damage of corners etc
EBay,
Do your homework and ask the seller to ensure the item is correct and to spec, avoid for critical parts
Diesel solutions Co. Durham
Fast efficient & economical check of injectors
HR auto specialists
Detailed in depth work carrying out my refurbishment, the right questions asked of me and open to all my suggestions / interference, very experienced knowledgeable staff
YMR metal solutions
Great quality items very little fettling required for fitting
LRS
Over all reasonable but sometimes send non OEM when specifically OEM ordered, slow to resolve these issues
Autosparks, Polevolt and Vehicle wiring products
All first class service for electrical items
Turner engineering
First class on all levels
Ashcrofts
Great as ever on all levels
Buzzweld
Great range of effective products, would buy again
Richards chassis
Lead time as quoted, excellent quality item minimal (as expected) fettling to fit
Devon 4x4
Wouldn't use again based on my experience
JGS 4x4
Useful source of parts quality good when OEM purchased
Land Rover
Hmmm found to be extremely overpriced with poor availably and apparent reluctance to engage with customer (no surprises there then)
As stated above by no means an exhaustive list
Not ranked and not an exhaustive list by any means but I can expand if the demand arises
Brit Car
Great customer service both for enquiries and any issues (minor) with items supplied, good source of genuine parts (all be it at a greater cost than the alternatives)
SP-4x4
Good quality items (Galv. doors) let down by poor packing resulting in minor damage of corners etc
EBay,
Do your homework and ask the seller to ensure the item is correct and to spec, avoid for critical parts
Diesel solutions Co. Durham
Fast efficient & economical check of injectors
HR auto specialists
Detailed in depth work carrying out my refurbishment, the right questions asked of me and open to all my suggestions / interference, very experienced knowledgeable staff
YMR metal solutions
Great quality items very little fettling required for fitting
LRS
Over all reasonable but sometimes send non OEM when specifically OEM ordered, slow to resolve these issues
Autosparks, Polevolt and Vehicle wiring products
All first class service for electrical items
Turner engineering
First class on all levels
Ashcrofts
Great as ever on all levels
Buzzweld
Great range of effective products, would buy again
Richards chassis
Lead time as quoted, excellent quality item minimal (as expected) fettling to fit
Devon 4x4
Wouldn't use again based on my experience
JGS 4x4
Useful source of parts quality good when OEM purchased
Land Rover
Hmmm found to be extremely overpriced with poor availably and apparent reluctance to engage with customer (no surprises there then)
As stated above by no means an exhaustive list
Last edited:
@Cavey_P38 already done
@Disco1BFG thanks, I'll give it another go
How are your front grilles attached ??
I'm fitting an air con front frame and want to know how your front grilles attach to the frame, is it fir tree fasteners (if so do they just push into the holes or do I need snap sacs?) or are there screws that screw into something ???? images would be appreciated thanks
I'm fitting an air con front frame and want to know how your front grilles attach to the frame, is it fir tree fasteners (if so do they just push into the holes or do I need snap sacs?) or are there screws that screw into something ???? images would be appreciated thanks
Last edited:
