dh-t

Member

• Feb 22, 2016

• #1

My rear washer as stopped washing.I have had the jet out and cleaned that out all ok.The pump runs ok and as far as I can tell there is no blockages,I know there is a non return valvue somewhere near the near side light cluster, I have searched high and low can I find it or the water tube no chance I know it is suposed to be there but I can't find it .ANY IDEAS. DH-T

 

wammers

No longer with us, RIP

Donater

• Feb 22, 2016

• #2

It is there when i do mine i'll let you know where i found it. But search higher rather than lower.

 

dh-t

Member

• Feb 22, 2016

• #3

Thank you I will keep an eye out.If you out around Forest of Bowland anytime pop in for a cuppa DH-T.

 

biketeacherdave

Well-Known Member

• Feb 22, 2016

• #4

Mine was well and truly blocked when I got it I gave it a few shots of air from the rear water jet end naughty I know but did the job.

 

Grrrrrr

Technician, Bodgit & Scarper Ltd

Full Member

• Feb 22, 2016

• #5

dh-t said:

Thank you I will keep an eye out.If you out around Forest of Bowland anytime pop in for a cuppa DH-T.

Click to expand...

Now that is a nice area. One of the secret lovely places in the country.

 

M

Martian

Active Member

• Feb 23, 2016

• #6

The rear washer water line runs down the outer edge of the near side alcove between the rear tailgate rubber seal and the rear quarterlight.

There are lots of cut outs and if you put your hand in the gap you will find the tubing hanging down.

The one way, (check), valve is located here and there should be sufficient spare tubing to allow you to remove it and check it, (no pun intended).

I had to replace my upper tailgate last month!

 

TAKdriver

Active Member

• Feb 23, 2016

• #7

Martian said:

The rear washer water line runs down the outer edge of the near side alcove between the rear tailgate rubber seal and the rear quarterlight.

There are lots of cut outs and if you put your hand in the gap you will find the tubing hanging down.

The one way, (check), valve is located here and there should be sufficient spare tubing to allow you to remove it and check it, (no pun intended).

I had to replace my upper tailgate last month!

Click to expand...

I don't want to hijack the thread but I'll be replacing mine over the summer ( replacement standing by for fitting).1. Any hints/tips/warnings ?
2. Is the valve just a pull out ? ( mine hasn't worked for 6 years !)

 

wammers

No longer with us, RIP

Donater

• Feb 23, 2016

• #8

TAKdriver said:

I don't want to hijack the thread but I'll be replacing mine over the summer ( replacement standing by for fitting).1. Any hints/tips/warnings ?
2. Is the valve just a pull out ? ( mine hasn't worked for 6 years !)

Click to expand...

Yeah wear a false nose and Micky Mouse ears when you are doing it. Won't make it any easier but will give the bloke next door something to talk about in the pub.

 

TAKdriver

Active Member

• Feb 23, 2016

• #9

wammers said:

Yeah wear a false nose and Micky Mouse ears when you are doing it. Won't make it any easier but will give the bloke next door something to talk about in the pub.

Click to expand...

I wouldn't have thought of that.....I'll let you know how it goes......is that all I should wear ? I'd hate to have an accident with the dipstick.

 

M

Martian

Active Member

• Feb 24, 2016

• #10

The task of replacing the valve really is simplicity itself - so get in there!

It should be possible to train any avian member of the Crow family to undertake the job - if you rig up some food as a final reward.

Just be respectful to your neighbours by not considering the clown outfit if you plan on doing the work in late October!

 

dh-t

Member

• Feb 24, 2016

• #11

Well Iv'e searched high and low and cant't find it anywhere,there is a clip in the place it should be but no tube,there is tubing up at the spray nozzle end going of to the right side of the car but that is where I loose it.I don't supose it being a ex police car would have anything to do with it.Well I will have to live with it for now or I should say without it. DH-T

 

M

Martian

Active Member

• Feb 24, 2016

• #12

I feel a 'Toyah' moment coming on - 'It's a mystery'!

It should be there and all I can suggest is to carefully pull out the gaitor, (between the upper tailgate and var body - where the heated windscreen and wiper motor cables are routed - along with the washer tubing), and gently pull the tubing from inside the car roof space area.

If yours has been cut/removed it will pull out easily but if it is just hidden you will feel resistance.

The upper trim comes off easily, (4 phillips screws I believe), and you can then chase it back all the way to just above the cd/sub woofer unit.

 

dh-t

Member

• Feb 25, 2016

• #13

Thanks for that,I know the tube goes from the nozzle back to the grommet as I had the wiper motor cover of the other day.but I didn't check from the grommet back,but it looks like it as been cut at some stage and the two ends have gone there own ways never to meet again,and I'm not going to rip the car apart on the chance I find them.Thank to eveyone who contributedv but it looks like a lost cause .