geordielad

Active Member
prop now reconed new bearings cv boot & ujs
cv boot vame from dave mac propshafts £16 + p&p (google)
no banging or vibrations now
ujs have grease nipples you will need the long ones to get the grease in then put short ones to stop fouling prop

DSCF1450.jpg

DSCF1451.jpg
 
Last edited:
ooooooo is the rubber/metal thing the thing that goes on this to fix it?

P2271842.jpg


imgur
 
Last edited:
yes its not a straight forward fit as you have to make the six holes slightly bigger but its a lot better than trying to fit a normal cv boot
 
Thanks for the info. When looking at the joint on mine I see there’s what looks like 3 metal onions at the end of the prop shaft, inside the collar. Will the rubber easily stretch over this or is there a trick to it?
 
I've got one of these boot replacement things now. Not fitted it yet. But I do have an update on the price.

£34 + vat = £40.80 (+ post). :eek:
 
Update. Fitted me new prop boot today. This new £40.80 one fitted without the need for cutting. Must be a different one to the one before.

Z9Mtk4m.jpg

DSCN2180 Z9Mtk4m
 
Last edited:
I appear to have f**ked up my gaiter today while bringing it back from the mechanics in my trailer. Got back and there was a thick black oil oozing out of the gaiter through a hole. Are these new gaiters easily fitted and the oil easily replaced?
 
There's 2 types. The crap original one which rips oft as soon as you fit it and the betterer one we prefer to fit. Best of luck choosing. ;)
 
Last edited:
This is from memory as it’s been a while since I did it.

Disconnect the front prop to ird connection.

DSCN2189.jpg


Remove all the bolts and slide the collar off.

Fa03Kaz.jpg

DSCN2179 Fa03Kaz

Remove the cir-clip off the end of the joint. You don’t need to remove the rollers. Be careful not to knock one off like I did. Hence the tie wrap to hold the needle bearings in place while I put the roller back.

WMM2cXM.jpg

DSCN2184 WMM2cXM

Should come off like this

kctOEX6.jpg

DSCN2178 kctOEX66

Pull the old clip/gaiter oft.

spaxYUY.jpg

DSCN2176 spaxYUY

Make sure the new gaiter fits over the collar and holes align.

Z9Mtk4m.jpg

DSCN2180 Z9Mtk4m

Now slide only the new gaiter and hose clip on the shaft. Fill with grease supplied with gaiter and fit the tripod joint carefully. Fit the cir-clip on the end of the shaft.

WMM2cXM.jpg

DSCN2184 WMM2cXM

Put some grease in the collar and slide onto the joint. Line up the collar and gaiter holes and secure with a tie wrap.

6EUfruF.jpg

DSCN2185 6EUfruF

Secure back to ird.
Tighten the hose clip round the shaft holding the end of the gaiter making sure the rubber isn’t pulled when the prop turns.
 
Last edited:
Do you know what size the bolts are that hold the prop bearing housing to the underside of the car
Thanks
 
m8x25mm with a 10mm head iirc, if you spit a cv its best to put it back with the rollers in same race they were running in
 
This is from memory as it’s been a while since I did it.

Disconnect the front prop to ird connection.

DSCN2189.jpg


Remove all the bolts and slide the collar off.

DSCN2179.jpg


Remove the cir-clip off the end of the joint. You don’t need to remove the rollers. Be careful not to knock one off like I did. Hence the tie wrap to hold the needle bearings in place while I put the roller back.

DSCN2184.jpg


Should come off like this

DSCN2178.jpg


Pull the old clip/gaiter oft.

DSCN2176.jpg


Make sure the new gaiter fits over the collar and holes align.

DSCN2180.jpg


Now slide only the new gaiter and hose clip on the shaft. Fill with grease supplied with gaiter and fit the tripod joint carefully. Fit the cir-clip on the end of the shaft.

DSCN2184.jpg


Put some grease in the collar and slide onto the joint. Line up the collar and gaiter holes and secure with a tie wrap.

DSCN2185.jpg


Secure back to ird.
Tighten the hose clip round the shaft holding the end of the gaiter making sure the rubber isn’t pulled when the prop turns.

Hi, my gaiter broke and I have been searching for a similar gaiter online but I can seem to locate one similar to the one on pic,
Please advice where i can get one.

Regards
 
Can't seem to move tripod bearing
Any ideas

I you can remove remove circlip you may have to take slightly stronger measures to dislodge the tripod bearing. On other cars I have had to resort to using two bits of wood to tap into bearing(usually place below either side of the shaft and using a downward motion on the shaft until the bearing make contact. Repeat until freed. My only caveat would be that, a seen from previous photos if one of the balls come off then it may end up with roller needle bearing hell a they make a bid for freedom. Other than that technique I can't see another option. Maybe others others to beg differ. Best of luck.
 

Similar threads