L

Larsern

Member

• Nov 5, 2017

• #1

During a headgasket change 18 months ago I changed the glowplugs with brand new Delphi plugs.
After cold start problems when the temperature has come down the last month I decided to check the plugs. 3 plugs of the 6 were dead. Measured and tested with 12v, no resistance and no visual damage.
Luckily I still had some old Beru plugs lying around. A quick swap and the motor is starting on the first rev.

Anybody with some similar experience with the Delphi plugs?

 

Mark Piercy

Well fumbled member....

Full Member

• Nov 5, 2017

• #2

I always go for Bosch, Delphi are better for filters, even their suspension components are middle of the road!!!

 

frog hopper

Well-Known Member

• Nov 5, 2017

• #3

Mark Piercy said:

I always go for Bosch, Delphi are better for filters, even their suspension components are middle of the road!!!

Click to expand...

Bummer, wish I hadn't read that, just had 4 Delphi plugs delivered ready for fitting next week.

 

Dopey

Well-Known Member

• Nov 5, 2017

• #4

Just change whats bad... then you wont feel the sting so much, or put new in and keep the good ones back

 

Grrrrrr

Technician, Bodgit & Scarper Ltd

Full Member

• Nov 6, 2017

• #5

Had Delphi on mine for years with no issues. In fact I probably ought to be thinking of replacing them.

 

N

N2O

Active Member

• Nov 17, 2017

• #6

Use only BERU for this engine, they heat up much faster than bosch junk.
Genuine ones are BERU.

 

Grrrrrr

Technician, Bodgit & Scarper Ltd

Full Member

• Nov 17, 2017

• #7

N2O said:

Use only BERU for this engine, they heat up much faster than bosch junk.
Genuine ones are BERU.

Click to expand...

Just finished putting Beru on mine and what a difference. One cycle of the glows and the starter barely moved before she caught and ran, and that's after sitting on the drive for over a week without moving and it is bl**dy freezing out there!

 

brianp38dse

Well-Known Member

• Nov 18, 2017

• #8

I haven't got a clue what makes fitted to mine as they were in the car when I got it 10 years ago my, might be about time to find out but not quite at the moment as still not allowed to do anything I am getting very very bored

 

Grrrrrr

Technician, Bodgit & Scarper Ltd

Full Member

• Nov 18, 2017

• #9

brianp38dse said:

I haven't got a clue what makes fitted to mine as they were in the car when I got it 10 years ago my, might be about time to find out but not quite at the moment as still not allowed to do anything I am getting very very bored

Click to expand...

Probably Beru from Land Rover. I won't be putting anything else in mine if they last as long as the last lot.

 

Grrrrrr

Technician, Bodgit & Scarper Ltd

Full Member

• Nov 18, 2017

• #10

Just put this up on another thread but putting a copy here for when people search.

The part number for the Eurocarparts website is 438110135 (RR P38A, M51 engine). £16.49 each before the discount code is applied. If you haven't got a discount code, get one! Normally there's one for the weekend. Failing that ring them up and they'll sort you out. With discount they're £66 the set.

The Land Rover part number is STC3103.

On the Beru website they show as GN013. http://beru.federalmogul.com/en-gb/e-catalogue/vehicle

 

brianp38dse

Well-Known Member

• Nov 18, 2017

• #11

Noted thank you, for when I do need to change mine