Colin from Hull · Mar 25, 2018

Hi
Went to my car p38 1997 4.0se Range Rover Friday evening to try and remove Eas fault and had not problems connecting and getting good idle.

Then went out Saturday afternoon and connected and couldn't get any comms, checked comm port and driver and everything seemed right....... so why doesn't it work.

Tried to load photos of my EAS to show you all but struggle with doing even that......I'm great with spanners but crap with laptops.....

Grrrrrr · Mar 26, 2018

Is the ODB plug good and clean? Connector behind the kick panel?

Orangebean · Mar 26, 2018

Have you checked the diagnostics fuse Colin? F33 IIRC.

Mark Piercy · Mar 26, 2018

Sometimes I have to swap between comms 4 and 5! Check as said above also.

Colin from Hull · Mar 28, 2018

Hi
I have checked the inline plug connection behind the side panel and the socket underneath which lead plugs into.... and all looks well, tried both comm's 6 and 8 same problem.
I will check fuse or do you mean relay.......I have swapped the EAS relay with another one....made no difference.
Thanks everyone for replies
Colin

Orangebean · Mar 28, 2018

Colin from Hull said:
I will check fuse or do you mean relay......

Fuse 33 is the power feed for diagnostics. If that blows, no diagnostics

Colin from Hull · Mar 28, 2018

Hi
Checked Fuse 33 5amp this is ok.........cheers!

Grrrrrr · Mar 28, 2018

Seem to remember if the delay timer relay has been replaced with a standard automotive relay then that will kill comms? By inference if it is toast then that would also kill it.

Have you tried the diag on a known good car?

wammers · Mar 29, 2018

Check fuses 24,33 and 44. You MUST have a functioning delay relay fitted.

Colin from Hull · Mar 30, 2018

Hi
Is the Delay Relay the one under the seat, I will check fuses later tonight.
No I haven't tried my diag on any other car.
I also got another lead (serial to USB) from work, this hasn't made any difference, tried it today.
I'm getting FF,1 FF,1 in Rx but only PP appears in Tx.
Cheers
Colin

brianp38dse · Mar 30, 2018

Yes the delay relay is the black one under passenger seat.

Colin from Hull · Apr 1, 2018

Hi
I have looked at all the fuses and everything is fine, I also swapped the delay relay with one from another Range Rover made no difference.
I also decided to try my Eas lead on my other Range Rover and Im getting same problem no IDLE.
so its got to be my lead.....right?
I did a continuity test on the lead......and only got readings on four pins would this be right.....how many wires/ pins are used used don't wiring diagram

wammers · Apr 1, 2018

Colin from Hull said:
Hi
I have looked at all the fuses and everything is fine, I also swapped the delay relay with one from another Range Rover made no difference.
I also decided to try my Eas lead on my other Range Rover and Im getting same problem no IDLE.
so its got to be my lead.....right?
I did a continuity test on the lead......and only got readings on four pins would this be right.....how many wires/ pins are used used don't wiring diagram

Did you put the driver for the USB to serial adaptor into your laptop BEFORE you connected to car. The generic Windows drivers usually do not work.

Orangebean · Apr 1, 2018

Colin from Hull said:
I did a continuity test on the lead......and only got readings on four pins would this be right.....how many wires/ pins are used used don't wiring diagram

OBD connector location 12 to DB9 location 3
OBD connector location 11 to DB9 location 2
OBD connector location 1 to DB9 location 7
OBD connector location 5 to DB9 location 5

Colin from Hull · Apr 1, 2018

Hi
When I have used this EAS lead before....I have just plugged in played never had anything to do with drivers. whilst having this problem I have followed these instruction........Go into Device Manager screen (Control Panel>System>Device Manager) and check which port the USB adapter has been assigned to and check that the drivers from the CD are assigned to it. Then ensure that the same COM port is selected in the EAS unlock program.

How do I check that the drivers from the CD are assigned to it, don't really know what this means and never had to this before when working correctly?
I have double clicked on the COM PORT which brings up a window stating 'this device is working properly

Colin from Hull · Apr 1, 2018

Hi
My continuity test does match yours Orangebean

Colin from Hull · Apr 4, 2018

Hi
Been on RSW Solutions website and in the list of FAQ is show my problem receiving PP in Rx is down to comm's problem, well I've gone into Device Manger seen which comms port and selected the same port before intialising.

Also been informed that continuity test of the OBD lead isn't good enough test to prove a good lead, its a bit more complicated at the ODB end.
So can anyone recommend a supplier of a new lead / EAS package.

wammers · Apr 4, 2018

Colin from Hull said:
Hi
Been on RSW Solutions website and in the list of FAQ is show my problem receiving PP in Rx is down to comm's problem, well I've gone into Device Manger seen which comms port and selected the same port before intialising.
Also been informed that continuity test of the OBD lead isn't good enough test to prove a good lead, its a bit more complicated at the ODB end.
So can anyone recommend a supplier of a new lead / EAS package.

Datatek on here PM him.

Grrrrrr · Apr 4, 2018

wammers said:
Datatek on here PM him.

+1.

Colin from Hull · Apr 4, 2018

Hi
Sent him a message
Just been given another thing to check which should prove everything is ok on my vehicle to get comms.
the OMD socket in my car...... I should have 12 volts on pins 4 and 16

Active Member

Technician, Bodgit & Scarper Ltd

Active Member

Well fumbled member....

Active Member

Active Member

Active Member

Technician, Bodgit & Scarper Ltd

No longer with us, RIP

Active Member

Well-Known Member

Active Member

No longer with us, RIP

Active Member

Active Member

Active Member

Active Member

No longer with us, RIP

Technician, Bodgit & Scarper Ltd

Active Member

Similar threads