Badger · Jul 16, 2010

I noticed today that the rear offside wheel hub was ' wet ' with oil and the actual wheel itself shows signs of oil spatter:

This pic shows the black ' lines ' which are oil spatter being thrown outwards

I picked up a haynes manual as well today, but with pics, it's probably best to ask on here for any tips/advice as to what could be causing this as it's not something i've found so far in the manual.

Cheers

thainy · Jul 16, 2010

change the cap and seal, see if that does it bud.

Series71 · Jul 16, 2010

i'd second that

sypher · Jul 16, 2010

also check your axle breather to see if its blocked .

parts wanted · Jul 16, 2010

All of the above had the same last week, new cap and its sorted so did em all.

Badger · Jul 17, 2010

Cheers all, will give that a look over the weekend :tea:

:EDIT:

Between haynes & Buster's guide for CV joint renewal, i assume the seal is the one with the bronze bush that would need replacing?

Guide here: http://www.landyzone.co.uk/lz/f41/cv-joint-renewal-68945.html

sypher said:
also check your axle breather to see if its blocked .

Will do that too mate, thanks

bustersbus · Jul 19, 2010

Aye as said above about changin' the rubber cap and blow yer breather pipe through to make sure it's not blocked

Oh, and yer back axle is a wee bit different to the front....

http://www.landyzone.co.uk/lz/f41/rear-stub-axle-renewal-89692.html

9no seal inside the stub axle

Badger · Jul 19, 2010

bustersbus said:
Aye as said above about changin' the rubber cap and blow yer breather pipe through to make sure it's not blocked

Oh, and yer back axle is a wee bit different to the front....

http://www.landyzone.co.uk/lz/f41/rear-stub-axle-renewal-89692.html

9no seal inside the stub axle

Cheers Buster, I'm glad you pointed out i was looking at the wrong hub ( easy mistake right? ) as i would've been scratchin' my 'ead abit when it came to do the job.

Checked Paddocks for replacement seals ( trackarm ends as well as they need doing ) but they list a fair few for a 90, any ideas where to get the correct part number? Tried the link on here but the site is down

bustersbus · Jul 19, 2010

PaulWilde said:
Cheers Buster, I'm glad you pointed out i was looking at the wrong hub ( easy mistake right? ) as i would've been scratchin' my 'ead abit when it came to do the job.

Checked Paddocks for replacement seals ( trackarm ends as well as they need doing ) but they list a fair few for a 90, any ideas where to get the correct part number? Tried the link on here but the site is down

Aye easy misake mate

The ones ah used are in here...

http://www.landyzone.co.uk/lz/f41/track-rod-ends-renewal-99508.html

And just checked me parts catalogue to make sure... and they're from 1987 onwards. Although my parts thingy is fur the 110, the parts are the same. Just checked lrseries to verify...

RTC5870 TRACK ROD END LH THREAD | shop | www.lrseries.com | L. R. Series

RTC5869 TRACK ROD END RH THREAD | shop | www.lrseries.com | L. R. Series

Badger · Jul 20, 2010

Thanks Buster

Badger

Well-Known Member

thainy

New Member

Series71

Space man

sypher

Well-Known Member

parts wanted

Active Member

Badger

Well-Known Member

bustersbus

Well-Known Member

Badger

Well-Known Member

bustersbus

Well-Known Member

Badger

Well-Known Member

Similar threads