gymmaniac · Nov 18, 2020

Hi all, anyone had success fitting one of these type things:

I've just lost perhaps 3 liters of oil while picking up the shopping. Tesco's probably weren't best pleased with the mess I made, oops.

Engine bay is rust proofed again for a while.

I'll have to take a look at the weekend to find where it was leaking from, everything is still tight though

Al2O3 · Nov 18, 2020

gymmaniac said:
Hi all, anyone had success fitting one of these type things:View attachment 223548

I've just lost perhaps 3 liters of oil while picking up the shopping. Tesco's probably weren't best pleased with the mess I made, oops.

Engine bay is rust proofed again for a while.

I'll have to take a look at the weekend to find where it was leaking from, everything is still tight though

Why have you fitted one of those?

frog hopper · Nov 19, 2020

What the kin ell is that for??

gymmaniac · Nov 19, 2020

frog hopper said:
What the kin ell is that for??

It acts as a spacer between the oil filter and housing so you can fit extra sensors. I've put an oil temp and oil pressure sensor on mine.

Al2O3 said:
Why have you fitted one of those?

For said sensors without disturbing the rest of the normal plumbing.
If I can't get it to seal at the weekend I think I'd be up for other options.

tottot · Nov 19, 2020

Have you fitted a gasket between it and the block ?

marjon · Nov 19, 2020

Its a sandwich with the oil filter? Yes? if so then you should only need a oil filter seal either side of it surely?

J

tottot · Nov 19, 2020

Oil filter seals come fitted to the oil filter, the adaptor has to have its own seal

gymmaniac · Nov 19, 2020

tottot said:
Have you fitted a gasket between it and the block ?

marjon said:
Its a sandwich with the oil filter? Yes? if so then you should only need a oil filter seal either side of it surely?
J

tottot said:
Oil filter seals come fitted to the oil filter, the adaptor has to have its own seal

It came with a double O-ring seal on one side, the other being blank. If the two faces aren't completely parallel then I guess either face could be sitting incorrectly.

Or perhaps I've fitted it upside down and it needed a new seal on top and the O-rings were to match with the oil filter?

jamesmartin · Nov 19, 2020

gymmaniac said:
It came with a double O-ring seal on one side, the other being blank. If the two faces aren't completely parallel then I guess either face could be sitting incorrectly.

Or perhaps I've fitted it upside down and it needed a new seal on top and the O-rings were to match with the oil filter?

the seal it came with seal it to the filter head the filter has its own seal so that side is bare

gymmaniac · Nov 19, 2020

Better images of the two sides

So which side does the oil filter connect to?

The top image would suggest oil filter on the flat side.

gymmaniac · Nov 19, 2020

jamesmartin said:
the seal it came with seal it to the filter head the filter has its own seal so that side is bare

Thanks James, I'm of the same opinion. So wondering how I've screwed it up.....

jamesmartin · Nov 19, 2020

gymmaniac said:
Better images of the two sides

So which side does the oil filter connect to?

The top image would suggest oil filter on the flat side.

bottom pic

marjon · Nov 19, 2020

gymmaniac said:
Thanks James, I'm of the same opinion. So wondering how I've screwed it up.....

How?

J

Al2O3 · Nov 19, 2020

So is there's a threaded tube, as per your first picture, that tightens the adapter on to the filter housing? The oil filter then fits to it?

gymmaniac · Nov 19, 2020

Al2O3 said:
So is there's a threaded tube, as per your first picture, that tightens the adapter on to the filter housing? The oil filter then fits to it?

yep, that's it. I'll also need to re-check the thread lengths to make sure that the threaded pipe (or whatever you call it) isn't bottoming out.

Al2O3 · Nov 19, 2020

gymmaniac said:
yep, that's it. I'll also need to re-check the thread lengths to make sure that the threaded pipe (or whatever you call it) isn't bottoming out.

That's what I was thinking. It doesn't take much to hand tighten an oil filter in place, so the adapter shouldn't need too much tightening up.

gymmaniac · Nov 21, 2020

Well it's not clearances.
There's enough engagement and clearance between the parts. I've had it apart 3 times today, best I could do was reduce the flow to a steady drip which seemed to come from the the top of the oil filter. The spacer is as flat and parallel as I can measure without a surface table. My bet is on the pipe/bolt inner/outer threads not being completely aligned, the oil filter then won't screw on flat.

As I don't want to add extra gaskets I think I'll have to go with an adapter into the normal oil pressure switch port: suggestions welcome.

cheers

gymmaniac · Nov 21, 2020

OK so I've had a look online and it looks like while it's easy to get an adapter for the pressure sensor (something like http://www.mattlewisracing.co.uk/product.php/1496/29/gauge_adaptor___matt_lewis_racing) it's not so easy to find an adapter that would take a temperature sensor as well.

My browsing suggests that you can take the oil temperature from the LT230 transfer box blanking plug location. As I've already got the gauge and sensor (https://www.ebay.co.uk/itm/Durite-0...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649) I'd prefer not to buy another kit (e.g. (https://www.onlinegearboxparts.com/product/8816/) as everything is wired in the dash already.

So I need an adapter to go between the sender I've got (1/8" NPFT) and the sump plug hole - which I believe takes part 608246 - so the hole should be 3/4" BSPP thread

Well then, I'll need an adapter with 3/4" BSPT and 1/8" NPFP ends then.

Am I talking crap?

gymmaniac · Nov 28, 2020

Found an adapter!

https://www.ebay.co.uk/itm/Male-BSP...ers-male-female/131225693084?var=430483501869

2nd time lucky

flat · Nov 28, 2020

gymmaniac said:
Found an adapter!

https://www.ebay.co.uk/itm/Male-BSP...ers-male-female/131225693084?var=430483501869

2nd time lucky

find yourself a T piece and then you can fit a sensor in to where the low level light sensor is, thats where I tee’d off for my oil pressure gauge

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads