D90mitch

D90mitch

Well-Known Member
Well after replacing the somewhat blackened oil on the 'new' to us V8 3.9 (EFI) with 10W40 semi synth which is what I read of a chart somewhere for the rover v8. After running the engine after the service it did sound quite a bit happer than before. However, I am now feeling a bit paranoid about if I have put the right oil in it! I have looked in many places and have found extremely varying answers. I'm very confused! I've read things from 0W30 to 20W30.

Is the 10w40 I have just put in ok?

:confused: :(
 
Yes my disco has always run on 10w40 from day one, 10w is just right for the ambient temps in my part of the world.
 
discool said:
Yes my disco has always run on 10w40 from day one, 10w is just right for the ambient temps in my part of the world.
Click to expand...

Good to hear, though I am sure I can hear a tappet going now I've had a closer listen this morning :( Maybe I'm just being paranoid but I am sure it's there. I'll get me neighbor to have a listen when he's back. A little worried. It's not that loud but I'm sure its there. Hard to hear over the sound of all the belts and things along with the cat rattling and the zorst burble.
 
20w 50 for rv8 as leyland tolerances never changed from 1970 to 1995 lol
 
10W40 is fine, ours has run on that since we did the engine rebuild 5 years ago, no problems.

We have used diesel oil rather than petrol, better spec and keeps it clean internally.

Peter
 
I think there later recommend of 10w40 semi was trying to pretend to everyone they had a modern engine under there when really it was a ww2 design! With a flat tappet engine you want lots of zinc in the oil such to the point real steel sell an additive as none of there fancy modern oils have any. Comma sonic is £12 for 5 liters trade price, has loads of zinc and exceeds the spec for the rv8 and it's also 20w50, save some cash and wear and try it :)
 
We had old cam followers, rockers etc in our engine and they are still there, nothing has changed dramatically over 60k miles, we know that one is a bit likely to lose pressure if standing with the valve open overnight and the spring pressure on the follower, but quite honestly it isn't something I think about.

I have a new camshaft and followers, bought them three years ago but they don't need replacing.

One of the hardest bits the engine has had to do was pulling up a long hill out of one of the valleys in Belgium, it goes on for about 10 miles and is a flat out 3rd gear slog with the big trailer behind. It survived that with no problems so I think the oil is OK.

Peter
 
Interesting, I have always put 20w50 Comma in the 71 Rangie, and 10w40 semi synth in the disco 3.9, I justified it to myself by saying the serpentine 3.9's have a better oil pump so can keep oil pressure up a bit better, the 3.5's with the old dizzy driven pump need that 20w50 to keep up oil pressure at idle especially when they're a bit worn, can't really see why it would matter to much though, regular oil changes are the key....
Comma oil is excellent value for money to IMO
 
It's the pre 76 sd1 pumps that were really poor, I updated mine in the 72 rangie with the high vol kit which brings it up to the later spec. Not sure the later pump changed I till the rotary one but they changed the oil grade in the book ages before that trying to look modern next to Toyota and the like lol
 
Mine is a pre serp efi engine. Dont know if any of you guys saw my post about being paranoid in the disco section? :rolleyes:
 
You must log in or register to reply here.

Similar threads

H
Oil Radiator Unions confusion
Replies
7
Views
644
Anaconda
A
D
New member/ new owner - Auto gearbox issues
Replies
1
Views
613
brianp38dse
brianp38dse
S
1993 discovery alarm
Replies
4
Views
486
Scott120160
S
Sulcalibur
Oil in coolant reservoir
Replies
4
Views
946
Nodge68
Nodge68
J
ZENITH CD175 TEMPERATURE COMPENSATORS HELPFUL INFO
Replies
8
Views
2K
hef19898
hef19898