toms3 · Sep 17, 2015

For the last month iv had a funny high pitch metallic rattling noise that when lift my foot off the clutch (the rattle lasts half a second ish) If I lift my foot off the accelerator quickly and my landrover jerks it does it severel times then then too. It's a 1987 landrover 90 with a disco 200 tdi engine fitted. About 6 months ago I fitted a new Valeo clutch kit, heavy duty fork arm and throw out bearing. It drives fine but this noise is getting me worried! Could it be a loose torsion spring or casing on clutch pressure plate? It's not been fitted long. I can't. See anything visable under there and it's recently had a new front prop. Any ideas anyone?

Cheers! Tom.

jimwyllie · Sep 17, 2015

If it only happens when you depress clutch pedal, particularly when stationary, the odds are on clutch release bearing

Take this with a pinch of salt, missed the bit where the OP said rattle last half a second!!

big si · Sep 17, 2015

Check ujs mate, i had a similar issue, breif high sound like washers spinning on a shaft just as clutch depressed or just as i let it out, was front prop uj at tbox ,didnt feel bad when i checked but was sloppy as hell once i dropped the prop off.

Thor1950 · Sep 17, 2015

throw out bearing talking to you. been in water and mud?

toms3 · Sep 17, 2015

big si said:
Check ujs mate, i had a similar issue, breif high sound like washers spinning on a shaft just as clutch depressed or just as i let it out, was front prop uj at tbox ,didnt feel bad when i checked but was sloppy as hell once i dropped the prop off.

cheers big si that sounds like my noise!

i replaced the front prop around a month ago (britpart) so i kind of overlooked the possability it could be that.

will greasing help? i gave it a good dose of grease before fitting. ill grease it tonight on my break and report back if it quietens down.

toms3 · Sep 17, 2015

jimwyllie said:
If it only happens when you depress clutch pedal, particularly when stationary, the odds are on clutch release bearing

Hi jimwillye i thaught about that too but its pretty new and i can tell its fine but thanks anyway!

Take this with a pinch of salt, missed the bit where the OP said rattle last half a second!!

Thor1950 said:
throw out bearing talking to you. been in water and mud?

hi Thor1950, iv not gone through anything bad to be honest just fields and odd boggy puddle

gemsdad · Sep 18, 2015

toms3 said:
cheers big si that sounds like my noise!

i replaced the front prop around a month ago (britpart) so i kind of overlooked the possability it could be that.

will greasing help? i gave it a good dose of grease before fitting. ill grease it tonight on my break and report back if it quietens down.

nail on head,britpart,check the prop asap,take it off to check it.

wattfield · Sep 18, 2015

Check all the nuts & bolts on the prop are still tight, or were tightened properly. If one's a bit loose it can rattle a bit.
It happened to me a friend of mine.

gemsdad · Sep 18, 2015

wattfield said:
Check all the nuts & bolts on the prop are still tight, or were tightened properly. If one's a bit loose it can rattle a bit.
It happened to me a friend of mine.

your friend is a plonker.

Brown · Sep 18, 2015

Yup, even though they're nylocks, it is possible for them to get loose. It happened on mine about 18 months ago. You notice a bit of a clunk or other noise on drive take up, so they don't get he chance to undo themselves very far before it starts producing symptoms.

toms3

Active Member

jimwyllie

Active Member

big si

Well-Known Member

Thor1950

Well-Known Member

toms3

Active Member

toms3

Active Member

gemsdad

NOT BOTHERED.

wattfield

AKA Dirk Diggler

gemsdad

NOT BOTHERED.

Brown

Well-Known Member

Similar threads