CohPC · Dec 10, 2022

So here's a pic of my bonnet, a rather sexy one, apart from 2 things, the 2 rubber grommets in the middle. Obviously previous owner didn't put the wheel mount back on when it was repainted and welded the rivet holes and put those grommets on the bolt holes which really annoys me.
I see there are 3 options
Plates under the holes, fill, sand repaint, lot of work for little reward
Replace bonnet, more cost similar amount of work to paint replacement bonnet.
Just put bonnet mount on , even if I don't put the wheel there it will look right.
If I do put wheel there it has more benefits;
Increased upper body strength
Increased value as we all know landys with wheel on bonnet are worth twice as much
Women will see me driving a landrover with a spare wheel on the bonnet and want to have sex with me (it may be a deluded fantasy but it's my deluded fantasy so please don't spoil it)
Any other options?

layfin · Dec 10, 2022

You need a bonnet with a recess in it to facilitate the spare wheel. Look out for an old military one.

CohPC · Dec 10, 2022

layfin said:
You need a bonnet with a recess in it to facilitate the spare wheel. Look out for an old military one.

For a deluxe bonnet you do the razor edge are lower and don't need it, this one's had one of before and has the strengthener underneath

marjon · Dec 10, 2022

One of these would cover the "ugly" holes and garner some attention

Drag FX Make Your Car Sound Like A V8 Muscle Car, OBD Synthetic Engine Sound Simulator: New Photos of the DragFX Audio Hood Scoop.

Just paint them body colour and get over your inadequacy. There's, loads more to fix I am sure

.

J

tottot · Dec 10, 2022

Fit a bonnet spare mount, it will look right and be right. My 63 2a Razor bonnet has one and there are no rubber support washers fitted around the mount.
They were not needed for the 600x16 tire standard on 88's of that time.

CohPC · Dec 10, 2022

tottot said:
Fit a bonnet spare mount, it will look right and be right. My 63 2a Razor bonnet has one and there are no rubber support washers fitted around the mount.
They were not needed for the 600x16 tire standard on 88's of that time.

My tyres are 650 so might need the rubbers

freelance · Dec 10, 2022

Just get the bloody thing dirty like a proper LR

CohPC · Dec 10, 2022

freelance said:
Just get the bloody thing dirty like a proper LR

It does get dirty, but it gets cleaned as well.

tottot · Dec 10, 2022

CohPC said:
My tyres are 650 so might need the rubbers

You wont need the rubbers, there is not much between 600 and 650 tires. 750's do in my experience.

dag019 · Dec 11, 2022

tottot said:
You wont need the rubbers, there is not much between 600 and 650 tires. 750's do in my experience.

I thought the rubbers were for when the tyre was flat? I didnt think any of them needed the rubber when an inflated tyre is fitted but when the tyre is flat the steel rim sits on the bonnet as it is not supported by an inflated tyre. The rubbers sit under the rim to prevent this in the event of a puncture. Or have I been misled!

Turboman · Dec 11, 2022

dag019 said:
I thought the rubbers were for when the tyre was flat? I didnt think any of them needed the rubber when an inflated tyre is fitted but when the tyre is flat the steel rim sits on the bonnet as it is not supported by an inflated tyre. The rubbers sit under the rim to prevent this in the event of a puncture. Or have I been misled!

As far as I know, the rubber bungs are there to stop the tyre rubbing the paint on the bonnet through vibration.
The bonnet skin is only made from soft alloy, so no reason a tyre could rub right through it over time without the rubber bungs.

tottot · Dec 11, 2022

Never tried putting a flat tire on the bonnet, just chucked em in the back.

dag019 · Dec 12, 2022

Turboman said:
As far as I know, the rubber bungs are there to stop the tyre rubbing the paint on the bonnet through vibration.
The bonnet skin is only made from soft alloy, so no reason a tyre could rub right through it over time without the rubber bungs.

Well if that is the case they defintily do not work on mine. I have a deluxe bonnet with 750 xzl’s and the edge lugs still contact the bonnet. I get a very nice pattern in the grub that likes to collect in the dished wheel well when I remove the spare.

Turboman · Dec 12, 2022

dag019 said:
Well if that is the case they defintily do not work on mine. I have a deluxe bonnet with 750 xzl’s and the edge lugs still contact the bonnet. I get a very nice pattern in the grub that likes to collect in the dished wheel well when I remove the spare.

Standard wheels?

dag019 · Dec 12, 2022

Turboman said:
Standard wheels?

HD “wolf” wheels, tubed version if it makes a difference.

Turboman · Dec 12, 2022

dag019 said:
HD “wolf” wheels, tubed version if it makes a difference.

It does, wider than standard rims, as far as I can remember.

dag019 · Dec 12, 2022

Turboman said:
It does, wider than standard rims, as far as I can remember.

6.5 width I believe. But surely that should mean there is less of a sidewall bulge on a 750 than a narrower rim.

Turboman · Dec 12, 2022

dag019 said:
6.5 width I believe. But surely that should mean there is less of a sidewall bulge on a 750 than a narrower rim.

Standard rim is 5.5 inches wide. Tyre bulge is up to the make of tyre, and tyre pressure.

dag019 · Dec 12, 2022

Turboman said:
Standard rim is 5.5 inches wide. Tyre bulge is up to the make of tyre, and tyre pressure.

Surely the same tyre on different rim widths has an effect and the wider the rim the smaller the sidewall bulge. That is why the silly boy racers and their ‘stretched’ tyres look so terrible:

tottot · Dec 12, 2022

dag019 said:
Well if that is the case they defintily do not work on mine. I have a deluxe bonnet with 750 xzl’s and the edge lugs still contact the bonnet. I get a very nice pattern in the grub that likes to collect in the dished wheel well when I remove the spare.

The deluxe bonnet is more or less flat in the wheel well so 7.50 tyre will rub. On a razor type the curve of the bonnet prevents the smaller 600/650 tyres from touching.

Well-Known Member

Attachments

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Mab An Gov

Well-Known Member

Well-Known Member

Mab An Gov

Well-Known Member

Mab An Gov

Well-Known Member

Mab An Gov

Well-Known Member

Well-Known Member

Similar threads