gibbs4626 · Jan 28, 2011

Hi
I have purchased some electric leather seats to replace my manual seats. Have got them in, but electrics not working as only have a lowline Becm. Unfortunately the new seats are leaning too far back and I need to adjust them. Any ideas how to do this manually. Even better can I operate the new seats from this Becm?

Datatek · Jan 28, 2011

gibbs4626 said:
Hi
I have purchased some electric leather seats to replace my manual seats. Have got them in, but electrics not working as only have a lowline Becm. Unfortunately the new seats are leaning too far back and I need to adjust them. Any ideas how to do this manually. Even better can I operate the new seats from this Becm?

You cannot operate the seats from a lowline BECM. If you are any good at electrics, it ought to be possible to rig them up to work indendant of the BECM.
:welcome2:

AndysP38 · Jan 20, 2012

Hi Guys,

I found this post on google and thought id ask a question!

As per Wills instructions i checked my BECM and it has a big H!

Can I add electric seats? I currently have 95 SE 4.0 P38. M reg first of the line!!

Thanks in advance

wills · Jan 21, 2012

It's been a while since I have done any work on my P38's seats, however, in theory you should be able to have the electric seats if you have the highline BeCM - im not sure what the spec of a 95 BeCM would be, however, if it has the H on then im sure you can get them in ok.

Anyway, you need to take out the driver's seat and look for connector C912 as shown in this photo...

If you have this then plugging the correct loom in and connecting the grounding eye to the point behind the BeCM should get them going - you may have to fit fuses 10 & 20 (both 30 amp) in the side of the BeCM if they are missing also.

If you get memory seats you additionally need to get the correct loom and make sure connector C907 is also present on your BeCM as shown below...

Make sure you disconnect the battery before installing any new seat loom as the grounding point you have to attach to is shared with other stuff.

Hope that helps

-Will

AndysP38 · Jan 23, 2012

Hi,

Thanks Wills, really appreciate the help!

I never thought about the memory option, Ill take a look.

It may not be the original Becm. A lot can happen in 17 years!!

Any ideas how to ID the becm to the car, so i can confirm its the original?

polsta · Nov 12, 2013

hi guys

bit of a bump on this, i have manual seats, but have an option on some electric in same color

i have a 96 DSE, im just going to check the bcem if highline in a minute when i go to work, it has heated seats, cruise control etc, so im hoping it does

couple of questions-
if it does, is there anything else i need to check ? are all electric seats +memory ? and if i get the seats, what else will i need ? just the looms ? will my heated seat looms have the electric seat plugs already on ? and/or are there different looms for electric, and electric memory seats ?

just trying to be clear on whats needed and to look for before getting the seats

thanks

gfromleeds · Nov 12, 2013

+1^
Ive got manual seats but a high line becm
would they just plug in and work or does it need programing in/extra parts if I fitted electric seats?

Rick-the-Pick · Nov 12, 2013

A highline becm has the capabilty to power the seats & sunroof. This is the difference between highline & lowline are these two options.

Be careful when purchasing a loom, as memory seats have an extra connector on the loom that plugs in under the seat, something heated/electric seat looms don't have.

gfromleeds · Nov 12, 2013

The hi-line is fitted in my dt because it has the optional climate control but im slowly bringing the spec up to dhse so the hi-line has/will come in usefull

gazzab79 · Nov 12, 2013

I've got some spare leather seats in lightstone. But they are not memory. In fact the seat back is manual. They are nappa though!

redrrover · Nov 30, 2013

Hi i have a 1996 dse i have just put all electric seats in you need the part wire loom from the r/r when you take seats out hore this helps Pete

fanatic · Nov 30, 2013

Search you need a highline bcem and sticker on it should tell you

gfromleeds · Dec 1, 2013

gazzab79 said:
I've got some spare leather seats in lightstone. But they are not memory. In fact the seat back is manual. They are nappa though!

How much we talking? I have gray leather at the min but both front seats have had it
Have thought about a colour change thpught if youve got any more parts

gibbs4626

New Member

Datatek

Well-Known Member

AndysP38

New Member

wills

Well-Known Member

AndysP38

New Member

polsta

Active Member

gfromleeds

Well-Known Member

Rick-the-Pick

Active Member

gfromleeds

Well-Known Member

gazzab79

New Member

redrrover

Member

fanatic

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

gfromleeds

Well-Known Member

Similar threads