On or around Tue, 24 Oct 2006 18:47:29 +0100, Ian Rawlings
<news06@tarcus.org.uk> enlightened us thusly:

>On 2006-10-24, Austin Shackles <austinNOSPAM@ddol-las.net> wrote:
>
>> what for?
>
>"Spring bolt -- axle journal"
>
>"Steering bolt sleeve -- front wheel drive housing"

I'd tend to assume from experience that more or less any threadlock will do.
My experience of things that the "book" says should be loctited is that for
the most part they don't come undone in normal use. Such things as brake
caliper bolts etc., which I've replaced in the past without thread lock,
have never come undone again.

There are a few occasions where the loctite is also providing a seal, where
a bolt goes into a water jacket on an engine, for example.
--
Austin Shackles. www.ddol-las.net my opinions are just that
0123456789112345678921234567893123456789412345678951234567896123456789712345
1 weebl: What's this? | in recognition of the fun that is weebl and bob
2 bob: it a SigRuler! | check out the weebl and bob archive:
3 weebl: How Handy! | http://www.weebl.jolt.co.uk/archives.php

On 2006-10-25, Austin Shackles <austinNOSPAM@ddol-las.net> wrote:

> I'd tend to assume from experience that more or less any threadlock will do.

That's my hope, although considering that I can't track down the
bloody parts it's supposed to be applied to, I'm still not sure that
it's a threadlock or bearing lock situation! I'm baffled as to where
these bits are, their descriptions don't match anything on the truck
at all, and neither do the part numbers.

Thankfully the most important bits are all sorted though, just these
two obscure ones remain.

--
Blast off and strike the evil Bydo empire!

Dougal wrote:
> Ian Rawlings wrote:
>
>> Wotcher all, not strictly landy, but I have a need for "loctite 636"
>> and/or "loctite 307", I don't know what they are but they appear to be
>> metal glues or threadlock/nutlock. Does anyone know what they are,
>> what their equivalents are or whether they're likely to be nutlock or
>> studlock? I can find almost no information on them, particularly
>> strength, so don't know if they're supposed to lock nuts or studs.
>>
>> Cheers to anyone with a 30-year-old loctite catalogue ;-)
>
>
> I should be able to find something at work tomorrow.

OK - here it is. This follows a discussion with Loctite UK.

Loctite 307

A high strength structural adhesive used for bonding flat, uncoated
metallic surfaces. Normally used with an activator/primer.

Today's nearest - Loctite 326 used with Activator 7649(Activator N).


Loctite 636

This is a bit 'grey' still. The product was never used in the UK and
no datasheet has been found yet (still hopeful, however). Strongly
believed to be an early version of 638 with possibly a slightly longer
cure time. It's a high strength retaining compound.

Today's nearest - Loctite 638. If a longer cure time is needed (very
unlikely) use Loctite 640.



I've got a copy of the 307 datasheet as an Acrobat file. Unfortunately
its from a scan and is 1.7MB. The others I mention later are tiny in
comparison.

If you want that, Ian, or those for the suggestions from the current
range I can send them to you. Is that e-mail address usable?

On 2006-10-25, Dougal <DougalAThiskennel.free-online.co.uk> wrote:

> Today's nearest - Loctite 326 used with Activator 7649(Activator N).
>
> Today's nearest - Loctite 638. If a longer cure time is needed (very
> unlikely) use Loctite 640.

Bleedin' marvellous, thanks muchly kind sir.

> If you want that, Ian, or those for the suggestions from the current
> range I can send them to you. Is that e-mail address usable?

The datasheets would be useful if you have the time to send them on,
just hit "reply to", I don't use invalid spamtraps, I just chuck the
email address after a year. If it's the slightest bit of hassle for
you though then please don't bother, you've been enough help already.

Thanks again! I'll file this away into my facts file.

--
Blast off and strike the evil Bydo empire!