jai_landrover · Aug 3, 2019

Hi fellow LZ people!

Long time no see been busy with trying to get landies out either trialling or racing on the odd occasion.

I have a new project I’m semi halfway down. It’s a slow project and very much on the cheap.

Want:
A base to camp when greenlaning, a base to stay when out at Weekender competitions. Strong off-road able
Trailer to carry camping equipment roof tent and tools support equipment.

I have a roof tent that is great however it renders the 90 unusable for most things. Can’t trial it too talk, can’t Greenlane it fear of ripping the tent off.

So what I need is a trailer that can be towed by my 90, hopefully put on the ifor Williams trailer with the racer behind for further afield events.

(This May prove tricky length and weight)

So here it goes I have a narrow track which will be the base. Ideally I wanted a wide track but funds and what popped up at the time means a narrow track will have to do for now.

jai_landrover · Aug 3, 2019

jai_landrover · Aug 3, 2019

A bit more ideas,

My Old Landy · Aug 3, 2019

I like what you have done with the front. Putting a tailgate in is a superb idea allowing access or transport of longer items.
Using a tub on a Sankey trailer appeals to me

I have seen one on the bay going for £6k

jai_landrover · Aug 3, 2019

I’m not wholly convinced about the tailgate yet.... I like the look however you cannot really remove it and the front needs some support. I am thinking about a landy radiator panel. Need to Measure. That way a set of LHD lamps could be in the trailer should you need to swap lamps over you have a set ready to go. Depends if I can get it to fit nicely

jai_landrover · Aug 7, 2019

Bit more work to see if I like the paint

benpalmer · Aug 9, 2019

Looking good. I'm watching with interest,Just started something very similar.

jai_landrover · Aug 16, 2019

Collected a 109 hard top and sides this evening.

I really want to cut the sides to half height to be able to keep the roof line low as possible and keep the roof tent equal to or under the 90’s roof line when being towed. Also allows access to store in an up and over garage type garage should that ever be needed.

Another big concern is being able to put onto a a bigger trailer for transport and not be too tall to be affected by trees wind towing etc

It will look a little funny and lose valuable space but I think it will be worth it.

benpalmer · Aug 16, 2019

jai_landrover said:
Collected a 109 hard top and sides this evening.

I really want to cut the sides to half height to be able to keep the roof line low as possible and keep the roof tent equal to or under the 90’s roof line when being towed. Also allows access to store in an up and over garage type garage should that ever be needed.

Another big concern is being able to put onto a a bigger trailer for transport and not be too tall to be affected by trees wind towing etc

It will look a little funny and lose valuable space but I think it will be worth it.

Was thinking of doing this also, the snag i found was that the side panels are angled, so if you cut them down the roof will be narrower than the shortened side panels. If that makes any sense....

jai_landrover · Aug 17, 2019

benpalmer said:
Was thinking of doing this also, the snag i found was that the side panels are angled, so if you cut them down the roof will be narrower than the shortened side panels. If that makes any sense....

Yea there is plenty of give and adjustment.

I’ve just fitted a 109 roof to Bros 109. Took the good and sticks off.

Placed the sides on the trailer. Latest idea is to sink the tent into the roof line. Means the tent needs to rotate 90 degrees and go off the side. We shall see. Might be better tbh

Neither really appeals. I will have 6 inch sides if I want to keep it low enough without sinking the tent into the roof.

jai_landrover · Aug 18, 2019

Today’s progress

kevstar · Aug 18, 2019

jai_landrover said:
View attachment 187235
View attachment 187236 View attachment 187237 View attachment 187238 View attachment 187239

Today’s progress

Looking good matey I recently bought a Sankey BDR trailer to kit out so im just collecting bits atm
ive got my D1 to finish first.

jai_landrover · Aug 18, 2019

My 90 is a wreck, I’ve got a half finished 80 series 1 CCV motor which needs attention lol

Plenty to be doing but the trailer is taking up the time at the moment. If the weather turns then i’ll be stashed away for a bit.

Still need a solution to keeping the tent low. So far thinking of sinking it into the roof and have it off one side.

kevstar · Aug 18, 2019

jai_landrover said:
My 90 is a wreck, I’ve got a half finished 80 series 1 CCV motor which needs attention lol

Plenty to be doing but the trailer is taking up the time at the moment. If the weather turns then i’ll be stashed away for a bit.

Still need a solution to keeping the tent low. So far thinking of sinking it into the roof and have it off one side.

What tent do you have ive not got mine yet I did think about a hard shell one but very pricey.

jai_landrover · Aug 18, 2019

kevstar said:
What tent do you have ive not got mine yet I did think about a hard shell one but very pricey.

It’s a cheap roof lodge thinking of maybe turning it sideways and cutting and bracing it. Will be horrible inside but maybe the answer

kevstar · Aug 18, 2019

jai_landrover said:
It’s a cheap roof lodge thinking of maybe turning it sideways and cutting and bracing it. Will be horrible inside but maybe the answerView attachment 187254

Could have it on a sliding shelf inside the trailer then pull it out & support it with drop down legs.

jai_landrover · Aug 18, 2019

Latest idea is in channel and slide it forward and down the front.

We shall see simple is always best

benpalmer · Aug 19, 2019

Good progress, starting to take shape. Like you I've been trying to think of a way to keep the tent inside the trailers so it doesn't get smashed into low branches etc while driving. It's really high when on top of the Defender. But I found that my roof tent is too wide to fit within the roof line. My latest idea that I'm working through is a sliding shelf as Kevstar said, about top of tub height. Would also keep it out of the wind when in use.

Either way, your progress is far quicker than mine so I'll get the benefit of watching you first.

Keep up the good work!

jai_landrover · Aug 19, 2019

benpalmer said:
Good progress, starting to take shape. Like you I've been trying to think of a way to keep the tent inside the trailers so it doesn't get smashed into low branches etc while driving. It's really high when on top of the Defender. But I found that my roof tent is too wide to fit within the roof line. My latest idea that I'm working through is a sliding shelf as Kevstar said, about top of tub height. Would also keep it out of the wind when in use.

Either way, your progress is far quicker than mine so I'll get the benefit of watching you first.

Keep up the good work!

Latest idea is (depending on length) slide it down the front. if your savvy you could put twin runners so you could position it up on top either facing rearwards or sideways.

Slow progress at the moment waiting on some bits to come.

After next pay day i need to put an order for a shed load of Steel and Ali.

Maybe a turn table thal locks in position..........

jai_landrover · Aug 21, 2019

Now it’s the boring bits!

Body panels and stuff Booo

Well-Known Member

Well-Known Member

Well-Known Member

Keep breathin'

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads