Salisbury Nick · Jul 27, 2022

Hi all, any pointers on where I should look to diagnose/fix the indicators not responding when they should?
I have a copy of RAVE but flicked through several hundred pages on my ipad and not found anything relevant yet. No reference to them in the manual for which fuse they are on, or could it be a relay?

Cheers
Nick

DanClarke · Jul 27, 2022

Do the hazards work? If they do then the wiring is probably OK.

Datatek · Jul 27, 2022

If the hazards work, it may well be a broken wire to the indicator stalk where it flexes.

Salisbury Nick · Jul 28, 2022

DanClarke said:
Do the hazards work? If they do then the wiring is probably OK.
View attachment 270242

Thanks to you and @Datatek - I’ll check and come back.

Salisbury Nick · Jul 28, 2022

Good news. Both hazards and indicators are actually working, it is just the audible ‘tick’ that has disappeared.

DanClarke · Jul 28, 2022

Salisbury Nick said:
Good news. Both hazards and indicators are actually working, it is just the audible ‘tick’ that has disappeared.

That "tick" is generated by the BeCM.

Salisbury Nick · Jul 28, 2022

DanClarke said:
That "tick" is generated by the BeCM.
View attachment 270307

Oh. It does not sound good then if it’s a BeCM fault?

DanClarke · Jul 28, 2022

Salisbury Nick said:
Oh. It does not sound good then if it’s a BeCM fault?

I think it is just a pulse/signal sent to a "sounder" of come kind. I just went to check mine and the sound itself is coming from somewhere inside the binnacle.
So it may just be a wiring fault or your sounder has gone bad. The sounder clicks in time with the lighting of the L/R turn binnacle lamp(s)

brianp38dse · Jul 28, 2022

On the back of the instrument cluster is a speaker that does all the dreaded beep beeps
Maybe someone has disconnected it so they can drive in piece with out fear.

DanClarke · Jul 28, 2022

brianp38dse said:
On the back of the instrument cluster is a speaker that does all the dreaded beep beeps
Maybe someone has disconnected it so they can drive in piece with out fear.

Easy way to check it is leave the key in the ignition and the drivers door open?
Mine beeps constantly and displays "Key in Ignition" until I remove the key OR close the door.

al-one-arm · Jul 30, 2022

years ago my indicators did not beep. at the same time the high/low transfer motor stopped working.i took the motor off made up some link wires to con the becm into thinking the motor was in high, and boom the indicators were beeping again.

Salisbury Nick · Aug 1, 2022

DanClarke said:
Easy way to check it is leave the key in the ignition and the drivers door open?
Mine beeps constantly and displays "Key in Ignition" until I remove the key OR close the door.

My L322 does that, but the p38 never has.

DanClarke · Aug 1, 2022

Salisbury Nick said:
My L322 does that, but the p38 never has.

Must be a software version thing then.

Datatek · Aug 1, 2022

Salisbury Nick said:
My L322 does that, but the p38 never has.

My P38's beep once with the message "key in ignition" when the drivers door is opened.

Salisbury Nick · Aug 1, 2022

Datatek said:
My P38's beep once with the message "key in ignition" when the drivers door is opened.

I’ll try that. Thanks.

Salisbury Nick

Well-Known Member

DanClarke

Well-Known Member

Datatek

Well-Known Member

Salisbury Nick

Well-Known Member

Salisbury Nick

Well-Known Member

DanClarke

Well-Known Member

Salisbury Nick

Well-Known Member

DanClarke

Well-Known Member

brianp38dse

Well-Known Member

DanClarke

Well-Known Member

al-one-arm

Well-Known Member

Salisbury Nick

Well-Known Member

DanClarke

Well-Known Member

Datatek

Well-Known Member

Salisbury Nick

Well-Known Member

Similar threads