I can't find the required diafram for me loo anywhere. The B&Q website said they had some but they dint. Been to a local hardware shop on the off-chance they might have one but they dint either, so I've had to order some off the bay which won't be here until next year ;)

Of course the old one was so brittle that the simple task of removing it has completely destroyed it so I have to keep turning the watta off in the house when the toilet is full. I would use the isolation valve behind the loo but that has never been turned since it was installed and the brass grub screw itself has seized in the valve and the head has rounded off. :rolleyes:
You poor sod, any chance of disconnecting it and capping it one way or another, then filling the cistern with buckets, or even simply flushing with them? Or buying another isolating valve and fitting that? Screwfix would be bound to have them. ;)
Best of luck :):):)
 
You poor sod, any chance of disconnecting it and capping it one way or another, then filling the cistern with buckets, or even simply flushing with them? Or buying another isolating valve and fitting that? Screwfix would be bound to have them. ;)
Best of luck :):):)
It's fine. Living by myself I don't use a lot of watta to be honest.
All me washing is done so I'll turn the watta off until I need a shower or fill the toilet cistern. :)
 
You poor sod, any chance of disconnecting it and capping it one way or another, then filling the cistern with buckets, or even simply flushing with them? Or buying another isolating valve and fitting that? Screwfix would be bound to have them. ;)
Best of luck :):):)
I got a stop cock that looks like a light switch .simple press to turn all the water off in the house.
Must remember to inform visitors what the blue switch does
(No cables/power etc done by water pressure)
 
....that I have made "some" progress with the "Lathe of errors".
The vendor has gone strangely quiet and has not responded to my questions requests for support.
I decided to take a "fix-it-or-fÜck-it" approach :eek: and so.....
I attacked it with a set of files and what were round holes for mounting studs are now vertical slots for mounting studs allowing some movement of the motor. ;)
I also fixed the awful placement of the drive pulley and where it had been hammered on I prised it off the motor shaft and used needle files to make it a better "slip-fit" and the pulley can now be adjusted along the shaft. ;)
I looked at the original belt and it is 90 tooth and 18 inches in total length but the fitting and fixing made it as tight as a bowstring because of a lack of adjustment capability of the motor (now-fixed).
Searching online I have found 3 alternative belts of the same tooth-pitch but of slightly larger tooth-counts and lengths and I am hopeful that one of them will meet the requirement and be within my "adjustment range" and a good fit. :rolleyes:
For good or ill I am committed to making this P.O.S. work as it should. :D
I will let y'all know how it goes. I promise. :)
 
You poor sod, any chance of disconnecting it and capping it one way or another, then filling the cistern with buckets, or even simply flushing with them? Or buying another isolating valve and fitting that? Screwfix would be bound to have them. ;)
Best of luck :):):)
Why does everything go on the blink at the weekend and holiday times? :( On Christmas eve I had two of my four outside lights give up. :(:( I've just replaced them - in time for a New Year's Eve blast off.
 
It's fine. Living by myself I don't use a lot of watta to be honest.
All me washing is done so I'll turn the watta off until I need a shower or fill the toilet cistern. :)
Yep, just fill a kettle and a jug or two.
Can't be worse than when we first moved into our place in France in the snow. no heating, no water, no electric!
Have a nice New Year all the same! If you can't drink the water...........!;););)
 
....that I have made "some" progress with the "Lathe of errors".
The vendor has gone strangely quiet and has not responded to my questions requests for support.
I decided to take a "fix-it-or-fÜck-it" approach :eek: and so.....
I attacked it with a set of files and what were round holes for mounting studs are now vertical slots for mounting studs allowing some movement of the motor. ;)
I also fixed the awful placement of the drive pulley and where it had been hammered on I prised it off the motor shaft and used needle files to make it a better "slip-fit" and the pulley can now be adjusted along the shaft. ;)
I looked at the original belt and it is 90 tooth and 18 inches in total length but the fitting and fixing made it as tight as a bowstring because of a lack of adjustment capability of the motor (now-fixed).
Searching online I have found 3 alternative belts of the same tooth-pitch but of slightly larger tooth-counts and lengths and I am hopeful that one of them will meet the requirement and be within my "adjustment range" and a good fit. :rolleyes:
For good or ill I am committed to making this P.O.S. work as it should. :D
I will let y'all know how it goes. I promise. :)
Well you've now done so much to it you will have little case with the vendor or the small claims track anyway! I think you are actually enjoying the challenge!
Best of luck with it all!:):):):)
 

Similar threads