Pablo63

Pablo63

Member
elp please parking sensors and cameras​
Report post​
So where to start, I have had an intermittent problem with my cameras and parking sensors not working for a while. Now they don’t work at all. I’ve been trying to diagnose the issue and had no joy.
I have an icar soft obd and I’m getting the faults with every sensor all codes B129c front left side sensor as an example. I try to clear codes and it changes to b1d58 rear sensor power circuit and another for front. My live date for my sensors shows my rears working apart from rear left which isn’t even an option and front have distance of 2.55mm. I have carried out continuity tests on all my harnesses and all good. I’ve also had a multimeter on all sensors and all showing virtually the same readings about 40. I took a guess at parking aid monitor as cant see how all sensors could be faulty but had no joy unless the used Pam is also faulty. When I disconnect my front bumper I can actually clear all faults however still have no cameras. As soon as I select reverse or re connect front fault is back and I get an audible warning like a parking sensor too close. So I guess it must be something to do with front. Sorry this is long winded but I’m out of ideas and I’m not one to go to dealer to sort. Would rather do it myself. Any ideas would be greatly appreciated. Thanks. Also just tried front sensors out of a 2014 Evoque that look the same and initially no warning beep when switched the car on. Checked cameras and all working then selected reverse and everything back to square one. No cameras or sensors.
 
Hi sorry it’s a l405 2013. And yes I can park but park every day in a busy car park with very short bays. So have to get extremely close to the car behind. It’s not really about being able to park it’s about something is not working and I want to fix it.
 
My understanding that for an L405 you need to use Topix to get access to wiring diagrams, etc. But if thye were intermittent, check & clean all the connectors. The nork that designed it probably programmed it to shutdown just because one tiddly component isn't working . . . . . to generate £££ for the stealers.
 
Yes had both bumpers off cleaned everything but no joy. Harnesses from Pam to all sensors good. All sensors seem to be good. Swapped parking aid module with used one and no change. Hoping someone had the same issue and resolved it. Have now found a wiring diagram but still can’t find it. Electrics isnt my strong point.
 

Attachments

  • PARKING AID Proximity camera system.pdf
    403.8 KB · Views: 101
  • PARKING AID Rear view camera.pdf
    128 KB · Views: 111
  • PARKING AID.pdf
    376 KB · Views: 127
Get a known good sensor and swap it out with the rears, one at a time - you don't need to re-mount the bumper cover to test, just have it connected and put the vehicle in reverse.
When you say a 'reading of 40' 40 what?
 
Thanks for your input. Resistance of 40 ohms all sensors read the same. Swapped sensors over from my Evoque which are good look identical but different part numbers. Have exactly the same readings as my vogue sensors. The rear left sensor which isn’t showing on my live data has been swapped with the right one and still no sign of rear left sensor but no fault code either.
 
Pablo63 said:
Hi sorry it’s a l405 2013. And yes I can park but park every day in a busy car park with very short bays. So have to get extremely close to the car behind. It’s not really about being able to park it’s about something is not working and I want to fix it.
Click to expand...
Land Rover owners have a saying: My crumple zone is your car :D :D :D :D 👍
 
Why are you testing resistance? on which pins? that is not a valid test for parking sensors on any test plan. Despite checking wiring, you could have poor pin grip, corrosion, volt drop in the harness or any combination of the above and more besides.
Clearly you need to start with the rear left sensor as there is no live data - find out why and you'll be on the way to fully diagnosing the fault. You should only be testing voltage, not resistance - 'resistance is futile' without a load applied, and you won't be able to measure resistance on a live circuit.
 
sorry I have voltage and earth on each sensor including rear left. And as I said electrics aren’t my thing. Don’t know how to test signal. I was checking resistance on pins to see if any of the sensors had different readings to possibly find an issue.
 
Graculus said:
Why are you testing resistance? on which pins? that is not a valid test for parking sensors on any test plan. Despite checking wiring, you could have poor pin grip, corrosion, volt drop in the harness or any combination of the above and more besides.
Clearly you need to start with the rear left sensor as there is no live data - find out why and you'll be on the way to fully diagnosing the fault. You should only be testing voltage, not resistance - 'resistance is futile' without a load applied, and you won't be able to measure resistance on a live circuit.
Click to expand...
Why would a resistance test not work resistance is not load dependent (unlike current) admittedly I know nothing about parking sensors despite having just swapped two over the weekend, I didn’t test them.
I would have thought that a resistance test between +ve and -ve pins would give a reasonable view. I have a failed and working sensor out of my car - I will give them a quick check and see
 
JokerUK said:
Why would a resistance test not work resistance is not load dependent (unlike current) admittedly I know nothing about parking sensors despite having just swapped two over the weekend, I didn’t test them.
I would have thought that a resistance test between +ve and -ve pins would give a reasonable view. I have a failed and working sensor out of my car - I will give them a quick check and see
Click to expand...
Ok couldn’t wait! Just got a working and non-working sensor with a meter set to 200k connecting between the two pins that are either side I get resistance of 34.8 on the working sensor and nothing on the duff one
 
You must log in or register to reply here.

Similar threads

B
New parking sensors back - still not working.
Replies
1
Views
440
Graculus
Graculus
kricktd5
L332 abs/ HDC
Replies
1
Views
848
Datatek
Datatek
rustyrangie
Classic fuel pump fuse location??
Replies
5
Views
211
Mark Piercy
Mark Piercy
Blob
L322 Parking Aid Module - what's the difference?
Replies
4
Views
565
pwood999
pwood999
F
New to the group
Replies
2
Views
529
brianp38dse
brianp38dse