currymunster · Nov 16, 2022

Hi, got a new MY98 Discovery 1 300tdi registered 1999 on a T plate.
Nice car but some monkey has been on it before me. Overtightening bolts.
Two water pump bolts female thread stripped.
1 Fan pulley bolt missing due to thread stripped.
Tensioner bolt stripped.
Exhaust manifold. 1 thread stripped in the cylinder head.
Waterpump and tensioner fixed.
Has anyone successfully helicoiled piston 4 exhaust manifold. The lower one nearest the bulkhead.
Just wondering if there is enough room to get a drill and tap in there?
I'm pretty sure a torque wrench don't cost much these days. Probably used a ½ inch drive ratchet on a 10mm socket.... ****s

lynall · Nov 16, 2022

currymunster said:
Hi, got a new MY98 Discovery 1 300tdi registered 1999 on a T plate.
Nice car but some monkey has been on it before me. Overtightening bolts.
Two water pump bolts female thread stripped.
1 Fan pulley bolt missing due to thread stripped.
Tensioner bolt stripped.
Exhaust manifold. 1 thread stripped in the cylinder head.
Waterpump and tensioner fixed.
Has anyone successfully helicoiled piston 4 exhaust manifold. The lower one nearest the bulkhead.
Just wondering if there is enough room to get a drill and tap in there?
I'm pretty sure a torque wrench don't cost much these days. Probably used a ½ inch drive ratchet on a 10mm socket.... ****s

Cheap helicoil kits on ebay under 30 quid with all sized included.

You used to be able to buy drill bits with a hex shank, which in your case could be driven by a ratchet spanner, but as 300 head easy to remove I would take the head off to make sure its a good job.
I have a selection of drills that I have cut down/resharpened for difficult access areas.

kevstar · Nov 16, 2022

currymunster said:
Hi, got a new MY98 Discovery 1 300tdi registered 1999 on a T plate.
Nice car but some monkey has been on it before me. Overtightening bolts.
Two water pump bolts female thread stripped.
1 Fan pulley bolt missing due to thread stripped.
Tensioner bolt stripped.
Exhaust manifold. 1 thread stripped in the cylinder head.
Waterpump and tensioner fixed.
Has anyone successfully helicoiled piston 4 exhaust manifold. The lower one nearest the bulkhead.
Just wondering if there is enough room to get a drill and tap in there?
I'm pretty sure a torque wrench don't cost much these days. Probably used a ½ inch drive ratchet on a 10mm socket.... ****s

Think its pretty tight where the lower one is one of these might be an option....

Henry_b · Nov 16, 2022

You can also get a 90 degree chuck adaptor for your regular drill for not much coin.

Stanleysteamer · Nov 16, 2022

kevstar said:
Think its pretty tight where the lower one is one of these might be an option....

Don't tell us, you're on commission!!!

currymunster · Nov 16, 2022

Cheers guys, I've got the helicoil kit already, I'm not keen taking the head off as I've only just done it this weekend with a victor reinz multilayer.
When I took it off I just thought it was loose. It wasn't till I reassembled that I realised it was already stripped. Too late by then......
I've worked on these engines so much and never stripped a thread. I can't believe I've found so many.
The two water pump threads were repaired by a local garage as my Amazon order wouldn't have been here in time
They used time sert which looked a lot better than helicoil. When I saw the price of time sert though....wow.
I've seen the angled chuck at Screwfix. I'll look into that.....
P gasket and head gasket done.
Phew

Stanleysteamer · Nov 16, 2022

I have had helicoils spin inside an ally head.
Don't trust them, if there's enough meat I always go a size or two bigger and tap a new thread. Then make a bigger hole in th thing that is being bolted to it.
Each to their own and all that!
Stan

kevstar · Nov 16, 2022

Stanleysteamer said:
Don't tell us, you're on commission!!!

I try my best

Stanleysteamer · Nov 16, 2022

kevstar said:
I try my best

Wot's your take on helicoils?
Points out of 10?

kevstar · Nov 16, 2022

Stanleysteamer said:
Wot's your take on helicoils?
Points out of 10?

They can be tricky in ally, all good if you can do them right personally id re-tap a bigger thread
& use a wider stud n drill the manifold if need be.

Stanleysteamer · Nov 16, 2022

kevstar said:
They can be tricky in ally, all good if you can do them right personally id re-tap a bigger thread
& use a wider stud n drill the manifold if need be.

Same as me then! Tis exactly what I did with the exhaust manifold on my D2.
A garage used helicoils on my Dolly Sprint head. Didn't last 5 minutes.

kevstar · Nov 16, 2022

Stanleysteamer said:
Same as me then! Tis exactly what I did with the exhaust manifold on my D2.
A garage used helicoils on my Dolly Sprint head. Didn't last 5 minutes.

Done it since I was a lad if your re-tapping a thread, why not just use a stud or bolt in it.

Stanleysteamer · Nov 16, 2022

kevstar said:
Done it since I was a lad if your re-tapping a thread, why not just use a stud or bolt in it.

Quite!
and if the female thread is fecked, drill it out and tap a new thread.
All that matters is having enough meat around the hole and no risk of cutting into a water or oilway!!

kevstar · Nov 16, 2022

Stanleysteamer said:
Quite!
and if the female thread is fecked, drill it out and tap a new thread.
All that matters is having enough meat around the hole and no risk of cutting into a water or oilway!!

Meat & hole in the one sentence just as well this aint AG

Stanleysteamer · Nov 16, 2022

kevstar said:
Meat & hole in the one sentence just as well this aint AG

Durdy bugre!!

kevstar · Nov 16, 2022

Stanleysteamer said:
Durdy bugre!!

Why thank you sir

KiwiTDI · Nov 17, 2022

currymunster said:
Hi, got a new MY98 Discovery 1 300tdi registered 1999 on a T plate.
Nice car but some monkey has been on it before me. Overtightening bolts.
Two water pump bolts female thread stripped.
1 Fan pulley bolt missing due to thread stripped.
Tensioner bolt stripped.
Exhaust manifold. 1 thread stripped in the cylinder head.
Waterpump and tensioner fixed.
Has anyone successfully helicoiled piston 4 exhaust manifold. The lower one nearest the bulkhead.
Just wondering if there is enough room to get a drill and tap in there?
I'm pretty sure a torque wrench don't cost much these days. Probably used a ½ inch drive ratchet on a 10mm socket.... ****s

just did the HG on my 300tdi and a PO had used a bolt where a stud should have been and it stripped when I did the bolt up (only then did I realise it should be a stud).

i fixed it by making a new stud out of a bolt, I made sure it had a longer thread than standard so it could engage with what was left of the thread deeper in the head, i used a tap to clean out the thread in the head first obviously. I did not do the nut up on this stud as tight as the others to give it max chance of holding, no leaks so far.

maybe there is enough thread left in your head for you to try this?

Stanleysteamer · Nov 17, 2022

KiwiTDI said:
just did the HG on my 300tdi and a PO had used a bolt where a stud should have been and it stripped when I did the bolt up (only then did I realise it should be a stud).

i fixed it by making a new stud out of a bolt, I made sure it had a longer thread than standard so it could engage with what was left of the thread deeper in the head, i used a tap to clean out the thread in the head first obviously. I did not do the nut up on this stud as tight as the others to give it max chance of holding, no leaks so far.

maybe there is enough thread left in your head for you to try this?

Hate to say this, but on a head stud that is a bit of a bodge, hope it holds.

Europa486 · Nov 17, 2022

For really tight places to drill I use a pancake drill,
They are readily available on eBay and used in aviation a lot,

https://www.browntool.com/Listview/tabid/344/ProductID/201/Default.aspx

Stanleysteamer · Nov 17, 2022

Europa486 said:
For really tight places to drill I use a pancake drill,
They are readily available on eBay and used in aviation a lot,

https://www.browntool.com/Listview/tabid/344/ProductID/201/Default.aspx

Like this, never seen one before.
Just a shame you need threaded drill bits which I also have never seen before.
But still very useful!
thanks for enlightening me!

Well-Known Member

Well-Known Member

Well-Known Member

Think outside, no box required.

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads