J

Jon Homer

Member

• Jan 11, 2018

• #1

Hi folks,
Hope you can help, I've recently picked up a hand throttle for my wife's S3 88" but need the 2 lever arms that fit onto the throttle linkage cross bar.
Hopefully someone on here can help more knows where I can pick them up.
Many thanks
Jon

 

J

John S

Well-Known Member

• Jan 12, 2018

• #2

Hand throttle was an optional extra so the parts numbers may not be listed or available.

 

R

rob1miles

Well-Known Member

• Jan 12, 2018

• #3

I have some possible numbers:
276013
569250
They are both levers on the cross shaft but are listed as "Diesel" although I suspect they are the same for petrol if the shaft is the same. Blanchards are listing 276013 which looks to be for the horizontal set up. 569250 looks to be for the vertical lever set up.

 

Blackburn

Well-Known Member

• Jan 12, 2018

• #4

Optional parts catalogue can be downloaded as PDF . Do a web search for Smithies landrover will bring up a NZ site of interest.

 

J

Jon Homer

Member

• Jan 12, 2018

• #5

Thanks for that guys, will take a look at Blanchard's later.
The parts numbers I have are 577127 & 592904 as Rob says above they are listed for the 2 1/4 diesel but can't see it would bidder on anyway to a petrol setup.

 

doobie

Active Member

• Jan 12, 2018

• #6

I have the parts for a hand throttle somewhere in my shed, I'll try look them out, might be a few days before I find them though.

 

J

Jon Homer

Member

• Jan 12, 2018

• #7

doobie said:

I have the parts for a hand throttle somewhere in my shed, I'll try look them out, might be a few days before I find them though.

Click to expand...

Thanks Doobie that would be great, give me a shout when you've found them out. Cheers

 

J

Jon Homer

Member

• Jan 19, 2018

• #8

Hi Doobie, did you get chance to have a look for those hand throttle bits?
Cheers
Jon

 

doobie

Active Member

• Jan 20, 2018

• #9

Jon Homer said:

Hi Doobie, did you get chance to have a look for those hand throttle bits?
Cheers
Jon

Click to expand...

I did but unfortunately I only found the actual hand throttle and link to the main throttle linkage but not the final arm that goes on the existing throttle linkages which I believe is the part you are after.
I have the same parts as in this ebay ad (this isn't my ad I just saw that it had the same parts as I can find)

 

J

Jon Homer

Member

• Jan 20, 2018

• #10

Ok thanks for looking, hex that's exactly what I've got as well.

 

Blackburn

Well-Known Member

• Jan 20, 2018

• #11

I have some pics of different set ups see attached pdf . I have a 200di so cable to fuel pump and old cross shaft is linked to hand throttle and acts on pedal shaft lever.

 

Attachments

• hand throttle.pdf

  464.8 KB · Views: 193

J

Jon Homer

Member

• Jan 24, 2018

• #12

[GALLERY=][/GALLERY]Thanks Blackburn, I've done a screen shot of the 2v levers that I'm after just to clarify, looks like you've extended yours on 1 of the pics, I assume that gives finer control?

 

Last edited: Jan 24, 2018

Blackburn

Well-Known Member

• Jan 24, 2018

• #13

The pics where not mine but info I gathered.
Mine attached but if your using all mechanical shafts to a carb not likely to be suitable.
Asmy injection pump is operated by the 1st lever at end of accelerator pedal rod , the hand throttle works in reverse and operates the bulkhead rod to change the throttle position.hence the extra link at that point

 

Attachments

• 
  DSCF1969.JPG

  208.8 KB · Views: 243
• 
  DSCF1968.JPG

  399.7 KB · Views: 182
• 
  DSCF1967.JPG

  278 KB · Views: 221
• 
  DSCF1966.JPG

  348.1 KB · Views: 204