border

border

Well-Known Member

Attachments

  • IMG_20210617_203439.jpg
    IMG_20210617_203439.jpg
    292.2 KB · Views: 143
Grease will be good for the CV in a defender, would have thought oil would be better for the UV in a series. Any grease would get washed off by the oil in any case?
 
kermit_rr said:
Grease will be good for the CV in a defender, would have thought oil would be better for the UV in a series. Any grease would get washed off by the oil in any case?
Click to expand...
Thats what a few have mentioned on other threads and forums.
So do they just fill diff with the usual diff oil and let it run through in to half shaft where UJs are fitted to lubricate everything, just wonder why they put the one shot grease in the kits for if not needed.
 
Had grease in mine for years, its an early axle with the spring loaded cones so no rialkos, been no issues.
 
border said:
Thats what a few have mentioned on other threads and forums.
So do they just fill diff with the usual diff oil and let it run through in to half shaft where UJs are fitted to lubricate everything, just wonder why they put the one shot grease in the kits for if not needed.
Click to expand...
I usually use the oil, but have often used the grease as well, both are fine.

The reason they went to grease is that you can be a bit more tolerant of leaky seals and pitted balls with the grease.

There is no problem with using both, they just mix in the housing. Make sure you never exceed the level of the filler/level plug whichever you use.
 
I don't suppose it really matters but I favour EP90 oil. The railco relies on splash lubrication, hence the need to lock up the freewheeling hubs often.
I modify the top kingpin to take a grease nipple + drill a hole/turn a groove and add a cross hole for the grease. The odd squirt with the grease gun gives peace of mind and the grease just mixes in with the oil.
 
The grease gets as thin as the oil when driving have grease in mine usually top up with some oil as easier to add when checking level. Never had and issue with top pin running dry.
 
Blackburn said:
The grease gets as thin as the oil when driving have grease in mine usually top up with some oil as easier to add when checking level. Never had and issue with top pin running dry.
Click to expand...
I agree. The "grease" is in fact pretty thin, especially when hot. I suspect it is actually oil mixed with a bit of graphited or similar grease, which would also account for the dark greenish colour.
 
tottot said:
Free wheel hubs are not a complete waist of time, something to stand on to look in engine bay.:D
Click to expand...
They are also quite useful for locating the wheel during wheel changes, they hold it up while you turn it round to get the studs behind the holes! :)

But as regards their stated purpose of saving fuel, I am doubtful.
 
I have found that the mpg does increase slightly with them off - enough to make a difference on my daily drive with fuel the price it is today so I only engage them when needed or for lubrication.
 
The one shot stuff is quite thin and runny as some have mentioned. Will pack them in first then see how it goes, mind you it will still be a while before its driving.
New oil seals in the axle ends so hopefully stop the ep 90 getting through and mixing the 2 together.
 
You must log in or register to reply here.

Similar threads

Frisol
Series 2a Gearbox - retaining compound, grease, and oil seal "compound"
Replies
5
Views
1K
Wildefalcon
W
yfo866
101 swivel hubs, grease or oil?
Replies
3
Views
2K
tottot
tottot
usna87
LT230 grinding noise?
Replies
6
Views
244
Maat
Maat
M
Spitting output housing from Transferbox
Replies
16
Views
567
miktdish
miktdish
proto57
Freelander 2 (LR2) Baffling (to me!) front Half-shaft/Axle Length Mystery! Too short, twice???
Replies
10
Views
876
Zorro587
Zorro587