xpuser8334 · May 3, 2017

Apparently... it's a hardened steel pin.
you should be able to knock it out somehow and replace it with something like the end off a HSS drill bit.
so... round!!

Charlot · May 4, 2017

Thanks. Yes that's what I'm thinking. Will use a drill bit and if necessary put a bit of welding on it to keep it in place if not tight enough. Will post the results. Or try making a step by step process with pics.

disco_mikey · May 4, 2017

Most often, it's the nylon bush that wears.

I had one 3D printed to replace mine when the clutch gets done, otherwise, it's only available as part of a new selector quadrant...

xpuser8334 · May 19, 2017

is 3D printing going to be man enough for the job @disco_mikey ?
I now have a spare box, so going to have a play when the weather allows!
Actually - Just broken a full 5dr Td4 (anyone want any doors and a bonnet in good nick?? - lol )

Nodge68 · May 19, 2017

xpuser8334 said:
is 3D printing going to be man enough for the job @disco_mikey ?
I now have a spare box, so going to have a play when the weather allows!
Actually - Just broken a full 5dr Td4 (anyone want any doors and a bonnet in good nick?? - lol )

No. But I need a centre console arm rest lid as mine is broken.

Charlot · May 19, 2017

@xpuser8334 please update with any reaults. Maybe do a batch if any good and sell them.
Also do you have the large rubber bushes from the upper and lower engin tiebar? Have been looking for them but can't find any. Have replaced them to polybushes but vibration is horrible so want to get back to rubber ones and only ones I found are complete with brackets. And put shipping cost up.

Charlot · May 19, 2017

Sry read wrong about the 3d printed part

xpuser8334 · May 19, 2017

DO you guya want ro drop me an email with the bits you want please.. look at my username and add hotmail,co,uk to the end..

Alibro · May 19, 2017

xpuser8334 said:
DO you guya want ro drop me an email with the bits you want please.. look at my username and add hotmail,co,uk to the end..

Is this the bush you're referring to?
https://www.muddymods.com/products/bush-gear-linkage-rear

disco_mikey · May 20, 2017

xpuser8334 said:
is 3D printing going to be man enough for the job @disco_mikey ?
I now have a spare box, so going to have a play when the weather allows!
Actually - Just broken a full 5dr Td4 (anyone want any doors and a bonnet in good nick?? - lol )

Hope so. One way to find out

Diesel Do · Apr 10, 2018

Just leave this here

xpuser8334 · Apr 24, 2018

Hmmm DieselDo..... do I assume we have met kind sir of the bearded kind?

oldken · Apr 28, 2018

duncanpage4 said:
I may have found something related to the problem!

I removed this part from the car today and noticed the tip looks very worn.
There is a lot of movement in the gear selector rods before it's even started to move the gear change selector shaft quadrant (as the Rave disc calls it).
Is it supposed to have a cam shape to it or is it supposed to be round?

Hi, This part on my Freelander looks like it is causing the 'wobbly gearstick' and I want to take it out and repair it
as suggested by Duncan. I am not sure how it is fixed in place., can it be done without removing engine/gearbox ??
Tips welcomed.
ken

Mervthecatfish · Nov 12, 2019

I cant see the picture in the post - but I think that's probably the same issue I have. Anyone got a picture please?

xpuser8334

Active Member

Charlot

Active Member

disco_mikey

Active Member

xpuser8334

Active Member

Nodge68

Well-Known Member

Charlot

Active Member

Charlot

Active Member

xpuser8334

Active Member

Alibro

Well-Known Member

disco_mikey

Active Member

Diesel Do

Well-Known Member

xpuser8334

Active Member

oldken

New Member

Mervthecatfish

New Member

Similar threads