Ging33

New Member
hi Iam new to 4x4 I just brought a freelander and I want to lift it 2 inch does anyone know where I can get a cheep set or 2nd hand one from thanks ging33
 
I all ready tried that with no luck there only one on eBay but they want £210 which is to dear for my budget that why after some sencond hand one :):)
 
I think island do one that works out about £175 with the dreaded, took about 4 seconds of searching to find it.

There was a bloke on eBay selling them for £50, but they looked very similar to some other ones and he disappeared one day
 
It's your vehicle and all, but remember that lift kits -- cheap or otherwise -- can get expensive when you have to replace parts that wear prematurely because of the kit.
 
Lift kits lift the body and give the wheels greater articulation. The lowest bits are your diff' and the front lower suspension arms. The only way to lift them and gain greater ground clearance is to fit taller tyres. Factory st'd tyres were 195/80/15 you could look at 215 or 225 75 15. The latter would give you about 25 mm lift.
A point to think about is tyre costs rise with bigger rim sizes.

Hope this helps.
 
I know Iam new to this but how does fitting a low profile make it taller 75 is less then 80 and mine all ready 16
 
The only advice I'd give is not to buy 'cheap' with something like that - they basically hold your suspension together - you don't want them breaking.

You should also search around on here because there are implications. As said above, bit (eg drive shafts) wear out a lot quicker - but you may also need to take chuncks out of the bodywork/chassis to allow for greater travel in the suspension and extend brake/ABS lines. You'll also want to get to get bigger tyres which cost and increase gearing which isn't a great thing without a low-range box. As a noob to 4x4 I would suggest you go out on some lanes with people who are experienced first, then decide how you want to adapt your car.
 
Been doing a lot of green lanes over xmas and found I need more clearance as keep hitting the ground
 
40mm lift and max 225/75/16 tyres (you may need spacers at thast size, is marginal) will give you the same clearance as a Defender. I regularly lane with a bunch in stock 90s and 110s and they still can't believe where a mildly lifted freelander will go.
 
The bits that are hitting the ground are not necessarily going to be raised with a lift kit. On my FL1 it's the lower front sus' arms, the engine bash plate [ a worthy mod' /accessory to fit! ] front cross and rear crossmember, diff ...

Re 'taller' tyres:
Your tyre sizes - 215/65/16 -
215 is the tyre width,
65 is its aspect ratio, that is the distance from the rim to the tread's 'face' - that distance in this case is 65% of the tyre's width which is nearly 140mm.
The 16 is the rim's diameter.
So, 215/65/16 has a diameter of 685.9mm
215/70/16 has a diameter of 707.4mm [ + 21.5mm from st'd] or a lift of about 10mm
225/70/16 has a diameter of 721.4mm [ + 35.5 from st'd] or a lift of about 18mm

You mightn't be able to get those tyres sizes.
If you do go for 'taller 70 or 75 series tyres' you may well need a lift kit and possibly wheel spacers as well to allow room for the larger tyres.

'Taller' tyres will effect performance, slower acceleration, and poorer fuel economy - except for long steady motorway driving where you may get an advantage!

A lift kit can effect handling, fuel economy [ increased air resistance?], ride quality and may cause drive train / suspension parts to wear more quickly.

Finally, rim width plays a key factor on the width of tyre you can fit. 16" rims are 6J or 6 inches wide. Best to consult your tyre supplier of specific tyre sizes for your FL. 16" tyres seem to be dearer than 15" and 17" more so again.

I've raised my FL1 with aftermarket springs and I hope to soon fit 215/75/15 MT on a spare set of rims. My diff'... should be about 25mm higher. Total clearance then should be 225 mm, possibly a bit more.

I hope everyone's contributions help and not confuse!
 
When I had a Freelander I fitted SES88's 40mm lift kit. The inner wheel arch needed to be cut away and the fuel pipe needed relocating. Then I had camber pins fitted to correct the suspension as it was all over the place. Then I had a proper 4 wheel laser alignment done on one of those expensive machines. I also fitted 215/70 R16 tyres (which are for sale in the for sale section) which further increased ground clearance. It ended up being roughly 75mm taller than a standard Freelander.

What I ended up with was ground clearance not dissimilar to a standard Defender. Not quite but very close. I went off-road and never never had a problem when out with Discos and Defenders.

It is not cheap fitting a lift kit if it is done properly and you have to pay somebody to do it.

Oh and the driveshafts went a year later. Not cheap. And the facelift ones were difficult to source oem ones as the cheap ones were crap and caused wobble through the steering.
 
I will be fitting it as Iam a mechanic and also own a 4 wheel laser tracking so I just need the spacers to do it then will get some bigger tyres after I lift so I know that I got good clearance for the bigger wheels have you got a link for the tyres you are selling thank ging33
 

Similar threads