Thinking about doing this, sound like an awsome project :)

but with one question, im on the brilliant ebay lol and i can only find '06 headlights.
will these work with the '04/'05 bumper on a 1999 1.8k Freelander?

mat
 
Hi Guys
just about to do this conversion again, last time i took pics, but not as detailed as is being done this time, going to be doing a cd with all the info on it. will upload wiring diagram start of next week.
I am going to go the full way this time and change the interior as well, the only problem i can see is the door panels, wiring is different , that can be changed ok, the other thing is the inside door opening handle, i am sure this has been covered before but cannot find the thread.
Any help appreciated
Stuart
 
I am going to go the full way this time and change the interior as well, the only problem i can see is the door panels, wiring is different

are you changing the dash too ? If so, be wary of this. The facelift dash (and some later pre-facelift ones too I think) are not compatable with the earlier ones. The early instruments used signals from the sensors direct to the pod, where they were displayed (eg fuel gauge). The later versions used CAN-BUS where all the signals were processed by the ecu, and then relayed up to the instrument pod.

can't remember who told me this, think it was clutchdust, quite some time ago. might be worth verifying before you take the old dash out.

good luck
 
The later versions used CAN-BUS where all the signals were processed by the ecu, and then relayed up to the instrument pod.


good luck

That part is definitely true - not sure of if, or when they changed to it, but my 04 model definitely uses CAN-BUS.
 
wrong post for this but.....

I've completed the facelift of my 2000 model, with wiring and everything (suprised myself their), but now im thinking of changing just the center dash console (gear stick, hand brake, radio etc.

has anyone done this, or does anyone know whether its possible?
 
wrong post for this but.....

I've completed the facelift of my 2000 model, with wiring and everything (suprised myself their), but now im thinking of changing just the center dash console (gear stick, hand brake, radio etc.

has anyone done this, or does anyone know whether its possible?

H'mm I think you might encounter difficulties with the hazard lights/fog lights switches - on 2004 onwards they're not part of the centre console and feature as part of the top of the dash. I seem to recall electric windows and central locking switches being located in the old centre console - on newer models these are in the doors. Again probably not impossible given access to the right materials from a newer model, but not that straightforward either!
 
Hi Guys
just about to do this conversion again, last time i took pics, but not as detailed as is being done this time, going to be doing a cd with all the info on it. will upload wiring diagram start of next week.
I am going to go the full way this time and change the interior as well, the only problem i can see is the door panels, wiring is different , that can be changed ok, the other thing is the inside door opening handle, i am sure this has been covered before but cannot find the thread.
Any help appreciated
Stuart

Stuart, as you seem to be going the whole hog will you be doing the powerfold mirrors as part of this conversion?
 
Hi i am a follower of this site the information is great but i need some sort of wiring diagram for my facelifted freelander
 
Hi all,
Currently in the latter stagesof the facelife on a 03 1.8 Freelander, can anyone out there tell me if they had to change the bumper support bar and what they did with the two recovery eyes, is it just a case of a bit careful trimming to help them fit. The wiring seemed to work out fine, just a bit of trial and error, not as daunting as it looks. Pretty hard to get a wiring diagram, unless everyone was using the same new plug with the same colours.

Thanks all
 
Hi All,

Ok i've just done my conversion yesterday, hacked my way through the headlamp frames and fitted the lights. I wasn't entirely sure how deep to cut the frame but tried and managed to fit both lights, comparing from mine to the pictures taken by Muply and Stuart, my headlamps doesn't seem to fit 100%. Still slightly sticking out.
Can anyone who has completed the facelift please take a photo of the recesses on your front panel so i can compare againts mine?


Thanks,
Rich
 
Hi All,

Ok i've just done my conversion yesterday, hacked my way through the headlamp frames and fitted the lights. I wasn't entirely sure how deep to cut the frame but tried and managed to fit both lights, comparing from mine to the pictures taken by Muply and Stuart, my headlamps doesn't seem to fit 100%. Still slightly sticking out.
Can anyone who has completed the facelift please take a photo of the recesses on your front panel so i can compare againts mine?


Thanks,
Rich



Maybe you could post some pictures of yours including the headlight cutouts, then the guys here could tell you where or if you've gone wrong.
 
I will c wot i can do ive just completed my second Facelift lol should be able to get pictures next week No ive lost the horn location Help
 
Thanks Muply,
I've hacked alittle bit further so now it's looking quite nicely fitted. Hmm I've been driving around to wreckers around here on oh boy it's so hard to get the plugs, i've been knocked back so many times it's getting depressing!! Are you able to hook me up with some please? hmm only problem is im in MELBOURNE! OZ! :(

Cheers,

Rich
 
2 x 2003/2007 headlights for the front with wiring plugs
1 x 2003/2006 fromt bumper
1 x 2003/2006 rear bumper
set of 2003/2006 rear upper lights
set of 2003/2006 lower rear lights

Paint for bumpers
Hammer to mod rear panel
angle grinder to trim front panel for headlight fitment

Thats it You can also upgrade rear panel to a TD4 STYLE one


Thanks Muply
 
Hi All
I ve just to do my face lift started on thr rear bumber but im having trouble it just wont sit right ? any idears where im going wrong
Matt
 
Great thread and great job Muply.

I would be very interested in a couple of those headlamp plugs if possible?

Also if anyone has the wiring diagram so that I can take a look that would be great.

I am just starting to source parts to complete the swap of the front bumper and headlamps intially on my 2001 TD4 ESX. if all goes to plan I may move onto doing teh rear bumper and panels also :)

Regards

Rob
 
Hi just about to start sourcing bits for my facelift on my 01 3dr TD4 any chance of sending me your pics the link from here keeps saying inactive

Cheers

Andy
 

Similar threads